Sears 113.197611, 113.197511 Attach Doors, Complete Center Slide Assembly, Only Drawer Model

Page 24

Assembly

Attach Doors

1. Set out: -two doors

-two magnetic catches with stop plates -four #6 x _/2"long pan head plastite

screws

-four #6 x ya" long pan head screws

-eight #10 x 1/2"long pan head plastite screws.

2. Put both doors face down on floor. At-

tach magnetic catch to inside surface of each door: use two #6 x v2" long screws per catch.

!

Magnetic Catch

Magnetic

Slop Plate

Doors

/\

f

¢

tJ

Magnetic Catches

3.Attach magnetic stop plate to each side of center support: use two #6 x 3!g'long screws per stop plate (insert screws through plate and into small holes).

4.Attach doors to hinges on side panels: use four #10 x 1/2"screws per door.

5.Go to "Attach Handwheel".

Complete Center Slide Assembly

(Only Drawer Model)

1. Set out

-center support -upper support

-rear support with four slide brackets attached

-two slide brackets

-sixteen _" diam x v_" long truss head screws

-sixteen v'4"diam lock washers -sixteen l/4" diam hex nuts.

Side

Panel

c

24

Image 24

Contents 113.197511 113.197611Part No. SP5539 Contents Safety Safety Symbol and Signal WordsMajor Hazards KWARNING Wrong Way Feed HazardSafety Instructions Personal Safety InstructionsWork Area Safety Instructions Saw Safety Instructions Workpiece Safety InstructionsBlade Safety Instructions On-Product Safety Labels KWARNINGSafety Assembly Identify PartsQJlIF*llfq!lt LHllLltlLllltllllltB Tools Needed For Assembly Assembly Steps Build Cabinet BaseBuild Foot Assemblies Shaped Slot Attach Foot Assemblies Short Assemble Side PanelsOnly Door Model without Casters Assembly Attach Door HingesAttach/Install Spacers Attach Side Panels to Bottom ShelfAttach Skirts Center Support Upper Lower Complete Center Slide Assembly Attach DoorsOnly Drawer Model Center Support Assemble Drawers Attach HandwheelMount Motor Shaft has left-hand threa&. Turn nut clock- wise to loosenAssembly Mount Basic Saw AssemblyAdjust Leveling Feet Attach Trim CapsInstall Front Table Attach Slide Arm SupportsClips. Note Table will extend about Beyond Trim caps Assemble Table Lock Mechanism Alignment and Adjustment Install Drawers Only Drawer ModelTo Remove Drawers Only Drawer Model Controls 45, -45 , 90Rip l.ock Controls Alignment and Adjustment Alignment and Adjustment StepsAdjust Column Support Level Front Table Square Crosscut Travel Install Blade Square Blade to Table for Crosscut- tingAlignment and Adjustment Square Blade to Fence Square Blade to Table for Ripping Adjust Carriage Bearings Make Blade Parallel to Table Install Guard Align Spreader to BladeComplete Adjustments Go to Digital Display Section and followError Messages Digital DisplayButton Functions =73Install Battery To Replace BatteryAlign Encoders Miter EncoderSet Zero Reference Points For Bevel, Miter, and Elevation Bevel EncoderSet Zero Reference Point For Rip Set Zero Reference Point For Out-RipConversion Table Motor Specifications Power SupplyMotor Protection & Reset Button Electrical ConnectionsTo Change Motor Voltage to 240 A.C To avoid electric shock, unplug sawBefore changing Motor voltage Crosscutting Safety CrosscuttingDuring crosscutting, blade teeth can Having fingers, hand or arm cut offCrosscuttin Crosscut KerfsMaking Crosscuts StepRepetitive Crosscutting Ripping Ripping DefinedIn-Rip and Out-Rip Positions Infeed and Outfeed DirectionsRipping Safety Workpiece PositioningKickback Pinching or binding can happen whenRipping Wrong Way FeedGuard Nose Function Pawls and Spreader FunctionRipping Set-up Procedure If workpiece is pushed along fenceWith kerfs, workpiece could get Making Rip Cuts InleedRipping Hints Dado Blades, Molding HeadsCutting Aides FencesPush Sticks Auxiliary Fence and Push Block for RippingCutting Aides Cutting Aides Straight Edge for Irregular WorkpieceAccessories Safety Information for DadoInformation for Edging Lower Blade Guard Edging without an auxiliary fenceAccessories Lower blade guard can get caught orJam in fence or table kerfs Maintenance CleaningGeneral Information LubricationAdjustments for Wear Remove screw and nut from swivel lock knobCarriage Bearings Arm and ColumnBlade Changing Replacing PawlsMotor Problem Possible CausesWhat to Do Troubleshooting Troubleshooting Cutting ProblemSaw Problem Possible CausesTroubleshooting Electronics ProblemBlank Repair Parts Model NOS .197411 and 113.197511Repair Parts Always order by Part Number Not by Key NumberModel NOS .197411 and 113.197611 Base and Column Assembly Model NOS .197411 and 113.197511 Parts List for Craftsman 10 Electronic Radial SAW Model NOS .197411 and 113.197611Model NOS .197411 and 113.197511 Model NOS .197411 and 113.197611 and 113,197511 PartRepair Parts ARM Assembly Table Assembly Foot Assembly Model 113.197511 Model NOS .197411, 113.197511 Repairs Parts Model NOS .197411, 113.197511Repairs Parts Cabinet Assembly for Model 113.197411 For ModelMotor Assembly Guard Assembly Index Sold by SEARS, Roebuck and CO., Chicago, IL 60684 U.S.A 113.197411Pail No. SP5539