Sears 113.197611, 113.197511, 113.197411 owner manual Safety

Page 9

On the side surface of the motor, visible from the infeed side when the saw is in a

rip position, is this safety label to alert you to outfeed zone hazard:

Near the saw handle is this safety label to alert you to thrown objects and to remind you to wear safety goggles:

On the bottom surface of the motor, visible when the cutting tool is horizontal, is this safety label to alert you use a guard

when edge molding, and to position cut-

ting tool behind fence: (see Accessories Section)

On the front panel is this general safety in-

struction label:

Safety

DANGER

, WARNING

DANGER

Image 9

Contents 113.197511 113.197611Part No. SP5539 Contents Safety Safety Symbol and Signal WordsMajor Hazards Wrong Way Feed Hazard KWARNINGSafety Instructions Personal Safety InstructionsWork Area Safety Instructions Workpiece Safety Instructions Saw Safety InstructionsBlade Safety Instructions KWARNING On-Product Safety LabelsSafety Identify Parts AssemblyQJlIF*llfq!lt LHllLltlLllltllllltB Tools Needed For Assembly Build Cabinet Base Assembly StepsBuild Foot Assemblies Shaped Slot Attach Foot Assemblies Short Assemble Side PanelsOnly Door Model without Casters Attach Door Hinges AssemblyAttach Side Panels to Bottom Shelf Attach/Install SpacersAttach Skirts Center Support Upper Lower Complete Center Slide Assembly Attach DoorsOnly Drawer Model Center Support Attach Handwheel Assemble DrawersShaft has left-hand threa&. Turn nut clock- wise to loosen Mount MotorMount Basic Saw Assembly AssemblyAttach Trim Caps Adjust Leveling FeetAttach Slide Arm Supports Install Front TableClips. Note Table will extend about Beyond Trim caps Assemble Table Lock Mechanism Alignment and Adjustment Install Drawers Only Drawer ModelTo Remove Drawers Only Drawer Model 45, -45 , 90 ControlsRip l.ock Controls Alignment and Adjustment Alignment and Adjustment StepsAdjust Column Support Level Front Table Square Crosscut Travel Square Blade to Table for Crosscut- ting Install BladeAlignment and Adjustment Square Blade to Fence Square Blade to Table for Ripping Adjust Carriage Bearings Make Blade Parallel to Table Align Spreader to Blade Install GuardGo to Digital Display Section and follow Complete AdjustmentsDigital Display Error MessagesButton Functions =73To Replace Battery Install BatteryMiter Encoder Align EncodersBevel Encoder Set Zero Reference Points For Bevel, Miter, and ElevationSet Zero Reference Point For Out-Rip Set Zero Reference Point For RipConversion Table Power Supply Motor SpecificationsElectrical Connections Motor Protection & Reset ButtonTo Change Motor Voltage to 240 A.C To avoid electric shock, unplug sawBefore changing Motor voltage Crosscutting Crosscutting SafetyDuring crosscutting, blade teeth can Having fingers, hand or arm cut offCrosscut Kerfs CrosscuttinStep Making CrosscutsRepetitive Crosscutting Ripping Defined RippingIn-Rip and Out-Rip Positions Infeed and Outfeed DirectionsWorkpiece Positioning Ripping SafetyPinching or binding can happen when KickbackWrong Way Feed RippingPawls and Spreader Function Guard Nose FunctionRipping Set-up Procedure If workpiece is pushed along fenceWith kerfs, workpiece could get Inleed Making Rip CutsDado Blades, Molding Heads Ripping HintsFences Cutting AidesPush Sticks Auxiliary Fence and Push Block for RippingCutting Aides Straight Edge for Irregular Workpiece Cutting AidesAccessories Safety Information for DadoInformation for Edging Edging without an auxiliary fence Lower Blade GuardAccessories Lower blade guard can get caught orJam in fence or table kerfs Cleaning MaintenanceGeneral Information LubricationRemove screw and nut from swivel lock knob Adjustments for WearArm and Column Carriage BearingsReplacing Pawls Blade ChangingMotor Problem Possible CausesWhat to Do Troubleshooting Cutting Problem TroubleshootingSaw Problem Possible CausesElectronics Problem TroubleshootingBlank Model NOS .197411 and 113.197511 Repair PartsAlways order by Part Number Not by Key Number Repair PartsModel NOS .197411 and 113.197611 Base and Column Assembly Model NOS .197411 and 113.197511 Model NOS .197411 and 113.197611 Parts List for Craftsman 10 Electronic Radial SAWModel NOS .197411 and 113.197511 Part Model NOS .197411 and 113.197611 and 113,197511Repair Parts ARM Assembly Table Assembly Foot Assembly Model 113.197511 Model NOS .197411, 113.197511 Model NOS .197411, 113.197511 Repairs PartsRepairs Parts Cabinet Assembly for Model 113.197411 Model ForMotor Assembly Guard Assembly Index Sold by SEARS, Roebuck and CO., Chicago, IL 60684 U.S.A 113.197411Pail No. SP5539