Sears 113.197611, 113.197511, 113.197411 owner manual Blade Changing, Replacing Pawls

Page 78

Maintenance

Rip Lock

If the blade carriage can be moved by pushing/pulling on the saw handle when the rip lock is locked, adjust:

1.Hold rip lock in unlocked position and tighten locknut one quarter turn.

2.Test adjustment: if carriage moves with difficulty, slightly loosen locknut; if car- riage moves easily, lock rip lock and try to move carriage along arm.

Replacing Pawls

Make sure the teeth of the pawls are al- ways sharp. If they become dull the pawls must be replaced:

1.Remove hex nut and old pawls.

2.Install new pawls and spreader.

3.Align spreader to blade according to in- structions in Alignment and Adjustment.

Blade Changing

To change the saw blade:

1.Turn switch off, remove yellow key, and unplug saw.

2.Use both blade wrenches in scissor ac- tion to loosen blade nut. Note:Arbor

shaft hc**left-hand thread_. Turn nut clock- wise to loosen.

3.Remove nut, blade collar, and blade. Insert new blade, making sure that arrow is on outside and points clockwise.

4. Re-install blade collar and nut. Note:

Do not overtighten nut because this can cause blade collar to warp and blade to wobble during cutting:

£rn =L 'ckNu

Rip-Lock	Cam	\
Level		Carriage Bolt

78

Image 78

Contents 113.197511 113.197611Part No. SP5539 Contents Safety Safety Symbol and Signal WordsMajor Hazards KWARNING Wrong Way Feed HazardSafety Instructions Personal Safety InstructionsWork Area Safety Instructions Saw Safety Instructions Workpiece Safety InstructionsBlade Safety Instructions On-Product Safety Labels KWARNINGSafety Assembly Identify PartsQJlIF*llfq!lt LHllLltlLllltllllltB Tools Needed For Assembly Assembly Steps Build Cabinet BaseBuild Foot Assemblies Shaped Slot Attach Foot Assemblies Short Assemble Side PanelsOnly Door Model without Casters Assembly Attach Door HingesAttach/Install Spacers Attach Side Panels to Bottom ShelfAttach Skirts Center Support Upper Lower Complete Center Slide Assembly Attach DoorsOnly Drawer Model Center Support Assemble Drawers Attach HandwheelMount Motor Shaft has left-hand threa&. Turn nut clock- wise to loosenAssembly Mount Basic Saw AssemblyAdjust Leveling Feet Attach Trim CapsInstall Front Table Attach Slide Arm SupportsClips. Note Table will extend about Beyond Trim caps Assemble Table Lock Mechanism Alignment and Adjustment Install Drawers Only Drawer ModelTo Remove Drawers Only Drawer Model Controls 45, -45 , 90Rip l.ock Controls Alignment and Adjustment Alignment and Adjustment StepsAdjust Column Support Level Front Table Square Crosscut Travel Install Blade Square Blade to Table for Crosscut- tingAlignment and Adjustment Square Blade to Fence Square Blade to Table for Ripping Adjust Carriage Bearings Make Blade Parallel to Table Install Guard Align Spreader to BladeComplete Adjustments Go to Digital Display Section and followButton Functions Error MessagesDigital Display =73Install Battery To Replace BatteryAlign Encoders Miter EncoderSet Zero Reference Points For Bevel, Miter, and Elevation Bevel EncoderSet Zero Reference Point For Rip Set Zero Reference Point For Out-RipConversion Table Motor Specifications Power SupplyMotor Protection & Reset Button Electrical ConnectionsTo Change Motor Voltage to 240 A.C To avoid electric shock, unplug sawBefore changing Motor voltage During crosscutting, blade teeth can Crosscutting SafetyCrosscutting Having fingers, hand or arm cut offCrosscuttin Crosscut KerfsMaking Crosscuts StepRepetitive Crosscutting In-Rip and Out-Rip Positions RippingRipping Defined Infeed and Outfeed DirectionsRipping Safety Workpiece PositioningKickback Pinching or binding can happen whenRipping Wrong Way FeedGuard Nose Function Pawls and Spreader FunctionRipping Set-up Procedure If workpiece is pushed along fenceWith kerfs, workpiece could get Making Rip Cuts InleedRipping Hints Dado Blades, Molding HeadsPush Sticks Cutting AidesFences Auxiliary Fence and Push Block for RippingCutting Aides Cutting Aides Straight Edge for Irregular WorkpieceAccessories Safety Information for DadoInformation for Edging Lower Blade Guard Edging without an auxiliary fenceAccessories Lower blade guard can get caught orJam in fence or table kerfs General Information MaintenanceCleaning LubricationAdjustments for Wear Remove screw and nut from swivel lock knobCarriage Bearings Arm and ColumnBlade Changing Replacing PawlsMotor Problem Possible CausesWhat to Do Troubleshooting Saw Problem TroubleshootingCutting Problem Possible CausesTroubleshooting Electronics ProblemBlank Repair Parts Model NOS .197411 and 113.197511Repair Parts Always order by Part Number Not by Key NumberModel NOS .197411 and 113.197611 Base and Column Assembly Model NOS .197411 and 113.197511 Parts List for Craftsman 10 Electronic Radial SAW Model NOS .197411 and 113.197611Model NOS .197411 and 113.197511 Model NOS .197411 and 113.197611 and 113,197511 PartRepair Parts ARM Assembly Table Assembly Foot Assembly Model 113.197511 Model NOS .197411, 113.197511 Repairs Parts Model NOS .197411, 113.197511Repairs Parts Cabinet Assembly for Model 113.197411 For ModelMotor Assembly Guard Assembly Index Sold by SEARS, Roebuck and CO., Chicago, IL 60684 U.S.A 113.197411Pail No. SP5539