Sears 113.197411, 113.197611, 113.197511 Cutting Aides, Straight Edge for Irregular Workpiece

Page 71

Cutting Aides

Clamp the featherboard to the front table, so that the angled edge of the feather-

board is against the workpiece on the in- feed side of the blade. Do not clamp the

featherboard against the cut off part (out-

feed side) of the workpiece. If clamped to

the outfeed side, the featherboard can squeeze the kerr closed, put binding pres- sure on the blade, and cause kickback.

Feather Board

This Side

Straight Edge for Irregular

Workpiece

WARNING

If you try to rip an irregular workpiece, it could bind blade and cause kickback.

If the workpiece you want to rip does not have a straight edge, attach a straight- edged board to the workpiece:

i)place irregular side of workpiece against fence

ii)put straight-edged board on top of workpiece and against fence

iii)tack straight edged board to workpiece.

Note: Straight-edged board must not extend

beyond leading end of workpiece and

should cover workpiece width only enough to pass between blade and fence.

Note: Use fence at least at high as com-

bined heights of workpiece and straight- edged board.

71

Image 71

Contents Part No. SP5539 113.197511113.197611 Contents Major Hazards SafetySafety Symbol and Signal Words Wrong Way Feed Hazard KWARNINGWork Area Safety Instructions Safety InstructionsPersonal Safety Instructions Workpiece Safety Instructions Saw Safety InstructionsBlade Safety Instructions KWARNING On-Product Safety LabelsSafety Identify Parts AssemblyQJlIF*llfq!lt LHllLltlLllltllllltB Tools Needed For Assembly Build Cabinet Base Assembly StepsBuild Foot Assemblies Shaped Slot Attach Foot Assemblies Short Assemble Side PanelsOnly Door Model without Casters Attach Door Hinges AssemblyAttach Side Panels to Bottom Shelf Attach/Install SpacersAttach Skirts Center Support Upper Lower Only Drawer Model Complete Center Slide AssemblyAttach Doors Center Support Attach Handwheel Assemble DrawersShaft has left-hand threa&. Turn nut clock- wise to loosen Mount MotorMount Basic Saw Assembly AssemblyAttach Trim Caps Adjust Leveling FeetAttach Slide Arm Supports Install Front TableClips. Note Table will extend about Beyond Trim caps Assemble Table Lock Mechanism To Remove Drawers Only Drawer Model Alignment and AdjustmentInstall Drawers Only Drawer Model 45, -45 , 90 ControlsRip l.ock Controls Adjust Column Support Alignment and AdjustmentAlignment and Adjustment Steps Level Front Table Square Crosscut Travel Square Blade to Table for Crosscut- ting Install BladeAlignment and Adjustment Square Blade to Fence Square Blade to Table for Ripping Adjust Carriage Bearings Make Blade Parallel to Table Align Spreader to Blade Install GuardGo to Digital Display Section and follow Complete Adjustments=73 Error MessagesDigital Display Button FunctionsTo Replace Battery Install BatteryMiter Encoder Align EncodersBevel Encoder Set Zero Reference Points For Bevel, Miter, and ElevationSet Zero Reference Point For Out-Rip Set Zero Reference Point For RipConversion Table Power Supply Motor SpecificationsElectrical Connections Motor Protection & Reset ButtonBefore changing Motor voltage To Change Motor Voltage to 240 A.CTo avoid electric shock, unplug saw Having fingers, hand or arm cut off Crosscutting SafetyCrosscutting During crosscutting, blade teeth canCrosscut Kerfs CrosscuttinStep Making CrosscutsRepetitive Crosscutting Infeed and Outfeed Directions RippingRipping Defined In-Rip and Out-Rip PositionsWorkpiece Positioning Ripping SafetyPinching or binding can happen when KickbackWrong Way Feed RippingPawls and Spreader Function Guard Nose FunctionWith kerfs, workpiece could get Ripping Set-up ProcedureIf workpiece is pushed along fence Inleed Making Rip CutsDado Blades, Molding Heads Ripping HintsAuxiliary Fence and Push Block for Ripping Cutting AidesFences Push SticksCutting Aides Straight Edge for Irregular Workpiece Cutting AidesInformation for Edging Accessories SafetyInformation for Dado Edging without an auxiliary fence Lower Blade GuardJam in fence or table kerfs AccessoriesLower blade guard can get caught or Lubrication MaintenanceCleaning General InformationRemove screw and nut from swivel lock knob Adjustments for WearArm and Column Carriage BearingsReplacing Pawls Blade ChangingWhat to Do Motor ProblemPossible Causes Troubleshooting Possible Causes TroubleshootingCutting Problem Saw ProblemElectronics Problem TroubleshootingBlank Model NOS .197411 and 113.197511 Repair PartsAlways order by Part Number Not by Key Number Repair PartsModel NOS .197411 and 113.197611 Base and Column Assembly Model NOS .197411 and 113.197511 Model NOS .197411 and 113.197611 Parts List for Craftsman 10 Electronic Radial SAWModel NOS .197411 and 113.197511 Part Model NOS .197411 and 113.197611 and 113,197511Repair Parts ARM Assembly Table Assembly Foot Assembly Model 113.197511 Model NOS .197411, 113.197511 Model NOS .197411, 113.197511 Repairs PartsRepairs Parts Cabinet Assembly for Model 113.197411 Model ForMotor Assembly Guard Assembly Index Pail No. SP5539 Sold by SEARS, Roebuck and CO., Chicago, IL 60684 U.S.A113.197411