Lincoln Electric IM805 manual Figure A.2 Connection of the Vantage to Premises Wiring

Page 15

A-7

INSTALLATION

A-7

2.Take necessary steps to assure load is limited to the capacity of the Vantage by installing a 50 amp, 240 VAC double pole circuit breaker. Maximum rated load for each leg of the 240 VAC auxiliary is 50 amps. Loading above the rated output will reduce output voltage below the allowable -10% of rated voltage which may damage appliances or other motor-driven equipment and may result in overheating of the Vantage engine.

3.Install a 50 amp 120/240 VAC plug (NEMA Type 14-50) to the double-pole circuit breaker using No. 6, 4 conductor cable of the desired length. (The 50 amp, 120/240 VAC plug is available in the optional K802R plug kit.)

4.Plug this cable into the 50 Amp 120/240 Volt receptacle on the Vantage case front.

Figure A.2 Connection of the Vantage to Premises Wiring

240Volt

60 Hz.

3-Wire

Service

240 VOLT

POWER

120 VOLT

COMPANY

120 VOLT

METER

GROUNDED CONDUCTOR

NEUTRAL

BUS

N

DOUBLE POLE DOUBLE THROW

LOAD

SWITCH RATING TO BE THE SAME

AS OR GREATER THAN PREMISES

SERVICE OVERCURRENT

PROTECTION.

PREMISES

DISCONNECT AND

SERVICE

GROUND

50AMP

OVERCURRENT

PROTECTION

240 VOLT

DOUBLE

50 AMP, 120/240

POLE

CIRCUIT

VOLT PLUG

240 VOLT

BREAKER

NEMA TYPE 14-50

GND

		N
50 AMP, 120/240 VOLT			NOTE: No. 6 COPPER CONDUCTOR CABLE SEE
RECEPTACLE			NOTE: No. 6 COPPER CONDUCTOR CABLE SEE
		NATIONAL ELECTRICAL CODE FOR ALTERNATE WIRE
			SIZE RECOMMENDATIONS.

Vantage 500 DEUTZ

Image 15

Contents Vantage 500 Deutz California Proposition 65 Warnings SafetyElectric Shock can kill Welding Sparks can cause fire or explosion Sûreté Pour Soudage a L’Arc Précautions DE SûretéThank You Table of Contents Vii Installation Installation Safety PrecautionsLocation / Ventilation Towing High Temperature OperationLifting High Altitude OperationPRE-OPERATION Engine Service Engine Cooling SystemEngine BREAK-IN Welding Terminals 5INSTALLATIONA-5Output Remote ControlAuxiliary Power Receptacles Standby Power ConnectionsFigure A.2 Connection of the Vantage to Premises Wiring Connection of LN-15 to the Vantage Connection of Lincoln Electric Wire FeedersConnection of AN LN-23P Wire Feeder to the Vantage Connection of LN-7, LN-8 or LN-742 to the VantageVantage 500 Deutz Connection of the LN-25 to the VantageSafety Instructions OperationGeneral Description RUN Controls and SettingsWelding Controls Items 9 through Stopping the Engine Auxiliary Power ControlsEngine Operation Starting the EngineWelder Operation For Tungsten Electrodes OperationAuxiliary Power Operation Operation Optional Field Installed Accessories AccessoriesMaintenance Routine and Periodic MaintenanceEngine Maintenance Secondary Fuel Filter Fuel PRE-FILTER/WATER Separator AssemblyFuel Filters Water Separator ElementCooling System Cooling Blower Belt Battery HandlingWelder / Generator Maintenance HOW to USE Troubleshooting Guide TroubleshootingPossible Areas Misadjustments Course of ActionFunction Problems 500 Connection Diagram DIAGRAMSF-2Diagram Commander / K867 / K775 / LN-7 Connection DiagramDiagrams Diagrams Commander / K867 / LN-8 Connection Diagram Diagrams Diagrams Engine Welders /LN-8 Connection Diagram Diagrams Diagrams Diagrams Diagrams Dimension Print Vantage 500 Deutz Inflammable Votre corps Avec des pièces sous tension Insulate yourself from workGround MojadaDébranchez le courant avant Utilisez un ventilateur ou un Keep your head out of fumes Turn power off before servicingGuards off Humos. Utilice ventilación o Servicio Aspiración para gases