Lincoln Electric IM805 manual Engine Welders /LN-8 Connection Diagram

Page 42

ENGINE WELDERS /LN-8 CONNECTION DIAGRAM

WARNING
ELECTRIC SHOCK can kill	MOVING PARTS can injure

Do not operate with panels open.	Keep guards in place.
Disconnect NEGATIVE (-) Battery lead	Keep away from moving parts.
before servicing.	Only qualified personnel should install,use
Do not touch electrically live parts.	or service this equipment.

CONNECTION DIAGRAM

F-9

Vantage 500 DEUTZ

14PIN AMPHENOL

+ _

CAUTION:

TO LN-8 INPUT

CABLE PLUG

K595 CONTROL CABLE

TO WORK

ELECTRODE CABLE

TO WIRE FEED UNIT

DIAGRAMS

ANY INCREASE OF THE HIGH IDLE ENGINE RPM BY CHANGING THE GOVERNOR SETTING OR OVERRIDING THE THROTTLE LINKAGE WILL CAUSE AN INCREASE IN THE AC WIRE FEEDER VOLTAGE, WHICH CAN DAMAGE THE CONTROL CIRCUIT. THE ENGINE GOVERNOR SETTING IS PRE-SET AT THE FACTORY – DO NOT ADJUST ABOVE RPM SPECIFICATIONS LISTED IN THE ENGINE WELDER OPERATING MANUAL.

N.A. WELDING CABLES MUST BE OF PROPER CAPACITY FOR THE CURRENT AND DUTY CYCLE OF IMMEDIATE AND FUTURE APPLICATIONS. SEE OPERATING MANUAL.

N.B. CONNECT WELDING CABLES TO OUTPUT STUDS FOR DESIRED POLARITY. POSITION THE WIRE FEEDER VOLTMETER SWITCH TO MATCH THE POLARITY OF THE ELECTRODE CABLE.

N.C. PLACE IDLER SWITCH IN “HIGH” POSITION.

4-14-2000

S24787-6

F-9

Image 42

Contents Vantage 500 Deutz Safety California Proposition 65 WarningsElectric Shock can kill Welding Sparks can cause fire or explosion Précautions DE Sûreté Sûreté Pour Soudage a L’ArcThank You Table of Contents Vii Installation Installation Safety PrecautionsLocation / Ventilation High Altitude Operation High Temperature OperationLifting TowingPRE-OPERATION Engine Service Engine Cooling SystemEngine BREAK-IN 5INSTALLATIONA-5 Welding TerminalsStandby Power Connections Remote ControlAuxiliary Power Receptacles OutputFigure A.2 Connection of the Vantage to Premises Wiring Connection of LN-7, LN-8 or LN-742 to the Vantage Connection of Lincoln Electric Wire FeedersConnection of AN LN-23P Wire Feeder to the Vantage Connection of LN-15 to the VantageConnection of the LN-25 to the Vantage Vantage 500 DeutzSafety Instructions OperationGeneral Description Controls and Settings RUNWelding Controls Items 9 through Starting the Engine Auxiliary Power ControlsEngine Operation Stopping the EngineWelder Operation Operation For Tungsten ElectrodesAuxiliary Power Operation Operation Accessories Optional Field Installed AccessoriesMaintenance Routine and Periodic MaintenanceEngine Maintenance Water Separator Element Fuel PRE-FILTER/WATER Separator AssemblyFuel Filters Secondary Fuel FilterBattery Handling Cooling System Cooling Blower BeltWelder / Generator Maintenance Troubleshooting HOW to USE Troubleshooting GuideMisadjustments Course of Action Possible AreasFunction Problems 500 DIAGRAMSF-2 Connection DiagramCommander / K867 / K775 / LN-7 Connection Diagram DiagramDiagrams Diagrams Commander / K867 / LN-8 Connection Diagram Diagrams Diagrams Engine Welders /LN-8 Connection Diagram Diagrams Diagrams Diagrams Diagrams Dimension Print Vantage 500 Deutz Mojada Insulate yourself from workGround Inflammable Votre corps Avec des pièces sous tensionHumos. Utilice ventilación o Servicio Aspiración para gases Keep your head out of fumes Turn power off before servicingGuards off Débranchez le courant avant Utilisez un ventilateur ou un