Lincoln Electric IM805 manual Commander / K867 / LN-8 Connection Diagram

Page 39

COMMANDER / K867 / LN-8 CONNECTION DIAGRAM

	WARNING
Do not operate with panels open.	Keep guards in place.
Disconnect NEGATIVE (-) BATTERY LEAD	Keep away from moving parts.
before servicing.	Only qualified personnel should install,use
Do not touch electrically live parts.	or service this equipment.

SPARE
82		LN-8
81	N.C.	WIRE
42	}	FEEDER
42
41

CONNECTION DIAGRAM

F-6

Vantage 500 DEUTZ

ELECTRODE

TO WORK

14PIN AMPHENOL

K867 UNIVERSAL

ADAPTER PLUG

31

32

2

4

21 GND

31

32

2

4

21

GND

K196

INPUT CABLE

DIAGRAMS

TO WORK

ELECTRODE CABLE

TO WIRE FEED UNIT

CAUTION :

75

76

77

} N.D.

A

B C

ANY INCREASE OF THE HIGH IDLE ENGINE RPM BY CHANGING THE GOVERNOR SETTING OR OVERRIDING THE THROTTLE LINKAGE WILL CAUSE

AN INCREASE IN THE THE AC AUXILIARY VOLTAGE. IF THIS VOLTAGE GOES OVER 140 VOLTS, WIRE FEEDER CONTROL CIRCUITS MAY BE

DAMAGED. THE ENGINE GOVERNOR SETTING IS PRE-SET AT THE FACTORY - DO NOT ADJUST ABOVE RPM SPECIFICATIONS LISTED IN

THE ENGINE WELDER OPERATING MANUAL.

N.A. WELDING CABLE MUST BE OF PROPER CAPACITY FOR THE CURRENT AND DUTY CYCLE OF IMMEDIATE AND FUTURE

APPICATIONS. SEE OPERATING MANUAL.

N.B. USE VOLTMETER SWITCH TO SELECT DESIRED ELECTRODE POLARITY. POSITION THE SELECTOR SWITCH TO "WIRE WELDING CV".

N.C. INSULATE EACH UNUSED LEAD INDIVIDUALLY.

N.D. SPLICE LEADS AND INSULATE.

7-2000

S23989

F-6

Image 39

Contents Vantage 500 Deutz California Proposition 65 Warnings SafetyElectric Shock can kill Welding Sparks can cause fire or explosion Sûreté Pour Soudage a L’Arc Précautions DE SûretéThank You Table of Contents Vii Installation Installation Safety PrecautionsLocation / Ventilation Towing High Temperature OperationLifting High Altitude OperationPRE-OPERATION Engine Service Engine Cooling SystemEngine BREAK-IN Welding Terminals 5INSTALLATIONA-5Output Remote ControlAuxiliary Power Receptacles Standby Power ConnectionsFigure A.2 Connection of the Vantage to Premises Wiring Connection of LN-15 to the Vantage Connection of Lincoln Electric Wire FeedersConnection of AN LN-23P Wire Feeder to the Vantage Connection of LN-7, LN-8 or LN-742 to the VantageVantage 500 Deutz Connection of the LN-25 to the VantageSafety Instructions OperationGeneral Description RUN Controls and SettingsWelding Controls Items 9 through Stopping the Engine Auxiliary Power ControlsEngine Operation Starting the EngineWelder Operation For Tungsten Electrodes OperationAuxiliary Power Operation Operation Optional Field Installed Accessories AccessoriesMaintenance Routine and Periodic MaintenanceEngine Maintenance Secondary Fuel Filter Fuel PRE-FILTER/WATER Separator AssemblyFuel Filters Water Separator ElementCooling System Cooling Blower Belt Battery HandlingWelder / Generator Maintenance HOW to USE Troubleshooting Guide TroubleshootingPossible Areas Misadjustments Course of ActionFunction Problems 500 Connection Diagram DIAGRAMSF-2Diagram Commander / K867 / K775 / LN-7 Connection DiagramDiagrams Diagrams Commander / K867 / LN-8 Connection Diagram Diagrams Diagrams Engine Welders /LN-8 Connection Diagram Diagrams Diagrams Diagrams Diagrams Dimension Print Vantage 500 Deutz Inflammable Votre corps Avec des pièces sous tension Insulate yourself from workGround MojadaDébranchez le courant avant Utilisez un ventilateur ou un Keep your head out of fumes Turn power off before servicingGuards off Humos. Utilice ventilación o Servicio Aspiración para gases