Hansol Multitech Uromat 3000 installation instructions Installing the Measuring Chamber

Page 45

Fig. 27

Fig. 28

2.15 Installing the Measuring Chamber

Lift up the tabletop (CFC panel) (Fig. 27/Pos. 1), it will be held by the gas spring.

Move the tabletop towards the back and remove the front Nirosta panel. Move the tabletop towards the front and remove the rear Nirosta panel. Remove the left (Fig. 27/Pos. 3) and right (Pos. 4) cover panels. Remove the screws for the spiral cable guide panel and remove the cable guide panel. Move the tabletop longitudinally, remove the 6 mounting screws in the polycarbonate panel (Pos. 2) and remove the polycarbonate panel towards the front.

Switch the unit into the service mode, the green LED on the controller goes on and stays on. Press the Store and Reset buttons on the control unit simultaneously, the three memory LED`s on the control unit will blink green and the LED on the controller will blink very rapidly.

The cassette Bucky can be moved slowly forward and backward using the Recall and Reset buttons.

Move the Bucky into the exposure position using the Recall button. Remove the grid frame (Fig. 28/Pos. 1) after removing the two screws (Pos. 3). Insert the measuring chamber into the holder (take note of the measuring chamber orientation) and secure it in place.

First lay the measuring chamber cable coming out of the wall through the corrugated hose (Fig. 23/ Pos. 9), through the back wall (Pos. 10), or the cable coming directly out of the floor, to the cable channel (Pos. 11) up and into the unit base.

Lay the measuring chamber cable parallel to the cables for the unit controller to the cable outlet (on the side of the unit base) (Fig. 25/Pos. 4).

Remove the corrugated hose holder (Fig. 26/Pos. 1). Pull the measuring chamber cable through the corrugated hose to the table. Insert the measuring chamber cable through the side frame box into the flexible plastic chain of the Bucky and bring it to the measuring chamber connector.

Caution:

The cable must be laid so that the cassette drive belt does not touch the cable. Then reinstall the grid frame. Reinstall the polycarbonate panel (Pos. 2).

06/00	- 45 of 90 -	0116 7201
Rev. 00 © 2000	Hans Pausch Röntgengerätebau Graf -Zeppelin-Str. 1	D-91056 Erlangen ALL RIGHTS RESERVED Ru

Image 45

Contents Installation Instructions Uromat Contents Adjustments Technical MaintenanceNot configured Component Weights General Safety InformationComponent Dimensions Packaging Dimensions and WeightsComponent Designations FFA Dimensional Drawing, Right-handed VersionFFA Dimensional Drawing, Left-handed Version345 Drehachse Dimensional Drawing for Floor Mounting, Left-handed Version 0116 06/00 Required Special Tools Power Line Connection DataRequired Test Equipment Conditions for Transport and StorageContents of Circuit Diagram Circuit Diagram,06/00 0116 Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Collimator connection Component Designations for the Circuit Diagram System Location Component FunctionUromat LED1 +A6 Terminal strip for Bucky Cassette box motor potentiometer Function Description of the Controller CPU Board BoardsBreaker Board Display Board Footswitch Board Control UnitUnpacking the Unit Preparations for MountingRemoving the Unit from the Pallet Installing the Unit Column Aligning the Unit Column Installing the Tube Unit Support Arm Temporarily Connecting Line PowerPreinstalling the Tube Unit Collimator Combination Laying the Collimator Cables Installing the Image Intensifier To lay cables in the unit, 7 meters are required Laying the High Voltage CablesPage Laying the I.I. Cable Making the Power Connection through the GeneratorInstalling the Measuring Chamber Installing the Tilt Angle Display- Error Display Installing the Grid Replacing the GridInstalling the Monitor Support Arm Option Installing the Cover PanelsSealing the Table Frame Cover Panel Installing the Mount for the Flush BowlTube Unit Support Arm AdjustmentCentral Beam Center of Bucky Central Beam CenterLengthwise to the tabletop, for this Movement Path Potentiometer, Tabletop longitudinal Movement Path Potentiometer, Tabletop transverse Bucky Cassette Tray Movement Path PotentiometerI.I. Carriage System Potentiometer Potentiometer 2 Table Tilt Movement Path Potentiometer 1 Table Tilt Movement PathTabletop Transverse Safety Switch Not configured Tabletop Longitudinal Safety Switch13 I.I. Carriage Movement Path Safety Switch Bucky Movement Path Safety SwitchTable Up Movement Path Switch Strike Plate Table Down Movement Path Switch Strike Plate16 -20 Tilt Movement Safety Switch 17 +88 Tilt Movement Safety SwitchSpindle Nut Safety Limit Switch Accessory Sensor Switches Tabletop longitudinal Belt TensionRaise-Lower Tabletop Belt Tension Cassette Carriage Drive Belt Tension Equipment Operation in the Service ModeProcedure Setting ParametersStartup Adjusting the AxesCollimator Basic Setting Setting the Collimator to the Cassette and I.I. Format Cassette FormatFormat Saving the Parameters in the PC Setup Parameters Electronic Adjustment ParametersTabletop long. Store yes/no 1/0 Mechanical and Electrical Checks Technical MaintenancePreparations Page Function Check Page Spare Parts, Overview 176Spare Parts, Unit Column Right-handed, Left-handed Versions 41/43 40/41 /10Spare Parts, Table Frame Tabletop, Right-handed Version 122 125 11 119 120 121 151Spare Parts, Table Frame Tabletop, Left-handed Version 128 135 185 136213 209 202 203 191 192 197 194 193 198 201 207 / 210 Spare Parts, Tube Unit Support Right-handed Version 193 191Spare Parts, Tube Unit Support Left-handed Version 209 207 / 210249 155 156 Spare Parts, AccessoriesPos Designation Spare Parts ListPos Designation Pos Designation Pos Designation Pos Designation Error Cause Corrective Measure Number TroubleshootingPage Version Update Board ReplacementMaintenance Verification Location of Identification Labels Labeling Overview of Labels Max kg/ 66 lb