Hansol Multitech Uromat 3000 Technical Maintenance, Mechanical and Electrical Checks

Page 67

4. Technical Maintenance

NOTE:

The maintenance described below must be performed every12 months.

If unit components need to be moved using the motor during maintenance, or if functions need to be checked while the unit is under power, the unit must be switched off immediately after reaching the new position or after completing the particular work step and the immediately disconnected from power again.

Components that are removed may only be replaced with original parts that are listed in the attached spare parts list. For maintenance, only acid-free grease may be used. Do not grease or oil bearings with seals.

4.1 Mechanical and Electrical Checks

Preparations:

-Move table to the max. up position.

-Switch power off to the system (line power)

-Remove the unit base cover cap

-Remove the unit base cover panels

-Remove the system carriage cover panels

Floor mounting:

-Check the unit column in both directions with the spirit level. Compensate any differences by using shims and retighten the mounting screws.

-Check the mounting screws for secure tightness. If needed, retighten. Torque 25 Nm (2.5 kpm)

Manual control unit:

-Check cable lead-in for good condition and for secure connection.

-Check the function of all buttons

-Check the function of all LED’s.

Multi-function footswitch:

-Check the cables for good condition and for secure connection. If necessary, replace damaged cables.

-Clean the spaces between the individual footswitches.

-Check all switch functions.

Fluoroscopy and exposure footswitch:

-Check the cables for good condition and for secure connection. If necessary, replace damaged cables.

-Clean the spaces between the individual footswitches.

-Check the switch functions.

06/00

- 67 of 90 -

0116 7201

Rev. 00 © 2000 Hans Pausch Röntgengerätebau Graf -Zeppelin-Str. 1 D-91056 Erlangen ALL RIGHTS RESERVED Ru

Image 67

Contents Installation Instructions Uromat Contents Technical Maintenance AdjustmentsNot configured Packaging Dimensions and Weights General Safety InformationComponent Weights Component DimensionsComponent Designations FFA Dimensional Drawing, Right-handed VersionFFA Dimensional Drawing, Left-handed Version345 Drehachse Dimensional Drawing for Floor Mounting, Left-handed Version 0116 06/00 Conditions for Transport and Storage Power Line Connection DataRequired Special Tools Required Test EquipmentContents of Circuit Diagram Circuit Diagram,06/00 0116 Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Collimator connection System Location Component Function Component Designations for the Circuit DiagramUromat LED1 +A6 Terminal strip for Bucky Cassette box motor potentiometer Function Description of the Controller CPU Board BoardsBreaker Board Display Board Footswitch Board Control UnitUnpacking the Unit Preparations for MountingRemoving the Unit from the Pallet Installing the Unit Column Aligning the Unit Column Installing the Tube Unit Support Arm Temporarily Connecting Line PowerPreinstalling the Tube Unit Collimator Combination Laying the Collimator Cables Installing the Image IntensifierTo lay cables in the unit, 7 meters are required Laying the High Voltage CablesPage Laying the I.I. Cable Making the Power Connection through the GeneratorInstalling the Measuring Chamber Installing the Tilt Angle Display- Error Display Installing the Grid Replacing the GridInstalling the Monitor Support Arm Option Installing the Cover PanelsSealing the Table Frame Cover Panel Installing the Mount for the Flush BowlTube Unit Support Arm AdjustmentCentral Beam Center Central Beam Center of BuckyLengthwise to the tabletop, for this Movement Path Potentiometer, Tabletop longitudinal Bucky Cassette Tray Movement Path Potentiometer Movement Path Potentiometer, Tabletop transverseI.I. Carriage System Potentiometer Potentiometer 2 Table Tilt Movement Path Potentiometer 1 Table Tilt Movement PathTabletop Transverse Safety Switch Not configured Tabletop Longitudinal Safety SwitchTable Down Movement Path Switch Strike Plate Bucky Movement Path Safety Switch13 I.I. Carriage Movement Path Safety Switch Table Up Movement Path Switch Strike Plate17 +88 Tilt Movement Safety Switch 16 -20 Tilt Movement Safety SwitchSpindle Nut Safety Limit Switch Tabletop longitudinal Belt Tension Accessory Sensor SwitchesRaise-Lower Tabletop Belt Tension Cassette Carriage Drive Belt Tension Equipment Operation in the Service ModeProcedure Setting ParametersStartup Adjusting the AxesCollimator Basic Setting Cassette Format Setting the Collimator to the Cassette and I.I. FormatFormat Saving the Parameters in the PC Setup Parameters Electronic Adjustment ParametersTabletop long. Store yes/no 1/0 Mechanical and Electrical Checks Technical MaintenancePreparations Page Function Check Page Spare Parts, Overview 176Spare Parts, Unit Column Right-handed, Left-handed Versions 41/43 40/41 /10Spare Parts, Table Frame Tabletop, Right-handed Version 122 125 11 119 120 121 151Spare Parts, Table Frame Tabletop, Left-handed Version 128 135 185 136213 209 202 203 191 192 197 194 193 198 201 207 / 210 Spare Parts, Tube Unit Support Right-handed Version 193 191Spare Parts, Tube Unit Support Left-handed Version 209 207 / 210249 155 156 Spare Parts, AccessoriesPos Designation Spare Parts ListPos Designation Pos Designation Pos Designation Pos Designation Error Cause Corrective Measure Number TroubleshootingPage Version Update Board ReplacementMaintenance Verification Location of Identification Labels Labeling Overview of Labels Max kg/ 66 lb