Hansol Multitech Uromat 3000 installation instructions Installing the Unit Column

Page 37

Install a spindle cross piece (Pos. 5+6) on each end of both support struts.

Remove the mounting screws (Fig. 07/Pos. 1+ Fig.06/Pos. 8) of the unit column from the pallet and press it down onto the pallet.

Use the 4 lift spindles (Fig. 06/Pos. 7) to evenly raise the unit until the transport pallet (Pos.9) is free and then slide it out from under the unit.

Install the 4 castors (Fig. 08/Pos. 3+4) (transport castors) for transport on the support studs (Pos. 1+2). Use the 4 lift spindles to lower the unit (with narrow transport pathways, remove the spindle cross pieces, Pos. 5+6) and move the unit to its installation location.

At the installation location, use the spindles to raise the unit until the castors are off the floor. Remove the castors and evenly lower the unit.

Caution:

The two support struts on the installation frame (Fig. 06/Pos. 1+2) may be removed only when the unit is secured to the floor.

Fig. 07

Fig. 08

2.4Installing the Unit Column

Remove the lower transport bracket (Fig. 05/Pos. 2) on the tube unit support arm.

While observing the tensile strength data that is listed on them, use the 6 heavy-duty load expansion bolts (for example, Liebig S12/40 or S12/65 expansion bolts) (Fig. 07/Pos. 1 and Fig. 09/Pos. 2).

Remove the transport frame (Fig. 06/Pos. 1+2).

Disengage the tube unit support arm (Fig. 03/Pos. 3) towards the top out of the unit base and carefully place it down on the floor next to the unit.

Disconnect the plug-in connector for the display.

Remove the cover panel on the unit base (Fig. 02/Pos. 1).

06/00

- 37 of 90 -

0116 7201

Rev. 00 © 2000 Hans Pausch Röntgengerätebau Graf -Zeppelin-Str. 1 D-91056 Erlangen ALL RIGHTS RESERVED Ru

Image 37
Contents Installation Instructions Uromat Contents Technical Maintenance AdjustmentsNot configured Component Weights General Safety InformationComponent Dimensions Packaging Dimensions and WeightsComponent Designations FFA Dimensional Drawing, Right-handed VersionFFA Dimensional Drawing, Left-handed Version345 Drehachse Dimensional Drawing for Floor Mounting, Left-handed Version 0116 06/00 Required Special Tools Power Line Connection DataRequired Test Equipment Conditions for Transport and StorageContents of Circuit Diagram Circuit Diagram,06/00 0116 Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Collimator connection System Location Component Function Component Designations for the Circuit DiagramUromat LED1 +A6 Terminal strip for Bucky Cassette box motor potentiometer Function Description of the Controller CPU Board BoardsBreaker Board Display Board Footswitch Board Control UnitUnpacking the Unit Preparations for MountingRemoving the Unit from the Pallet Installing the Unit Column Aligning the Unit Column Installing the Tube Unit Support Arm Temporarily Connecting Line PowerPreinstalling the Tube Unit Collimator Combination Laying the Collimator Cables Installing the Image IntensifierTo lay cables in the unit, 7 meters are required Laying the High Voltage CablesPage Laying the I.I. Cable Making the Power Connection through the GeneratorInstalling the Measuring Chamber Installing the Tilt Angle Display- Error Display Installing the Grid Replacing the GridInstalling the Monitor Support Arm Option Installing the Cover PanelsSealing the Table Frame Cover Panel Installing the Mount for the Flush BowlTube Unit Support Arm AdjustmentCentral Beam Center Central Beam Center of BuckyLengthwise to the tabletop, for this Movement Path Potentiometer, Tabletop longitudinal Bucky Cassette Tray Movement Path Potentiometer Movement Path Potentiometer, Tabletop transverseI.I. Carriage System Potentiometer Potentiometer 2 Table Tilt Movement Path Potentiometer 1 Table Tilt Movement PathTabletop Transverse Safety Switch Not configured Tabletop Longitudinal Safety Switch13 I.I. Carriage Movement Path Safety Switch Bucky Movement Path Safety SwitchTable Up Movement Path Switch Strike Plate Table Down Movement Path Switch Strike Plate17 +88 Tilt Movement Safety Switch 16 -20 Tilt Movement Safety SwitchSpindle Nut Safety Limit Switch Tabletop longitudinal Belt Tension Accessory Sensor SwitchesRaise-Lower Tabletop Belt Tension Cassette Carriage Drive Belt Tension Equipment Operation in the Service ModeProcedure Setting ParametersStartup Adjusting the AxesCollimator Basic Setting Cassette Format Setting the Collimator to the Cassette and I.I. FormatFormat Saving the Parameters in the PC Setup Parameters Electronic Adjustment ParametersTabletop long. Store yes/no 1/0 Mechanical and Electrical Checks Technical MaintenancePreparations Page Function Check Page Spare Parts, Overview 176Spare Parts, Unit Column Right-handed, Left-handed Versions 41/43 40/41 /10Spare Parts, Table Frame Tabletop, Right-handed Version 122 125 11 119 120 121 151Spare Parts, Table Frame Tabletop, Left-handed Version 128 135 185 136213 209 202 203 191 192 197 194 193 198 201 207 / 210 Spare Parts, Tube Unit Support Right-handed Version 193 191Spare Parts, Tube Unit Support Left-handed Version 209 207 / 210249 155 156 Spare Parts, AccessoriesPos Designation Spare Parts ListPos Designation Pos Designation Pos Designation Pos Designation Error Cause Corrective Measure Number TroubleshootingPage Version Update Board ReplacementMaintenance Verification Location of Identification Labels Labeling Overview of Labels Max kg/ 66 lb