Hansol Multitech Uromat 3000 installation instructions Startup, Adjusting the Axes

Page 61

f. Display Self Test

After switching on power, all segments in the tilt display and the large round LED’s are tested individually. If this does not happen, there is a malfunction.

Seven-segment display: visible by a circular sequence of the active segments. All segments must light up. If a segment does not go on, there is a malfunction.

LED’s: All three LED’s light up cyclically in the three colors: red, green and yellow. If one color does not appear, there is a malfunction.

g. Footswitch Self Test

This test cannot be viewed. However, correct function is signaled via the bus.

h. Control Unit Self Test

After switching on power, all LED’s are individually tested by blinking, the multi-colored LED’s also blink in the three colors. If this does not happen, there is a malfunction.

3.24 Startup

Adjusting the Axes

If a PC is not available, proceed as described below:

Switch the unit with the switch (Fig. 76/Pos. 1) into the service mode, the green LED (Pos. 2) on the controller goes on and stays on.

Press the Store and Reset buttons on the control unit at the same time, the three memory LED`s on the control unit blink green and the LED on the controller blinks very quickly.

Each axis can now be moved normally. Exception: the cassette can be moved slowly forward and backward by pressing the Recall and Reset buttons.

To save a new software limit, Store must be pressed and held (M1 LED blinks red) and the corresponding direction button for the desired movement must also be pressed.

If the controller has recognized this correctly, the M1 LED blinks red, and the position has been accepted and the keys can be released again. The M1 LED then blinks green again. To save a centered position, the Store button must again be pressed and held and then the two buttons for the corresponding axis must either be pressed and held, or pressed in sequence.

To move past an incorrectly set software limit, the ZOOM button must be held down and the corresponding direction button must also be held. The software limit is now set to the maximum AD value.

If an axis is completely adjusted, the new limits should be saved in the EEprom. To do this, the Store and Reset buttons must be pressed at the same time. During the save routine (approx. 5 sec) all three memory LED’s will blink red.

When the save routine is completed, the memory LED`s will again blink green.

06/00

- 61 of 90 -

0116 7201

Rev. 00 © 2000 Hans Pausch Röntgengerätebau Graf -Zeppelin-Str. 1 D-91056 Erlangen ALL RIGHTS RESERVED Ru

Page 60 Page 62
Image 61
Page 60 Page 62
Contents Installation Instructions Uromat Contents Technical Maintenance AdjustmentsNot configured Component Weights General Safety InformationComponent Dimensions Packaging Dimensions and WeightsComponent Designations FFA Dimensional Drawing, Right-handed VersionFFA Dimensional Drawing, Left-handed Version345 Drehachse Dimensional Drawing for Floor Mounting, Left-handed Version 0116 06/00 Required Special Tools Power Line Connection DataRequired Test Equipment Conditions for Transport and StorageContents of Circuit Diagram Circuit Diagram,06/00 0116 Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Collimator connection System Location Component Function Component Designations for the Circuit DiagramUromat LED1 +A6 Terminal strip for Bucky Cassette box motor potentiometer Function Description of the Controller CPU Board BoardsBreaker Board Display Board Footswitch Board Control UnitUnpacking the Unit Preparations for MountingRemoving the Unit from the Pallet Installing the Unit Column Aligning the Unit Column Installing the Tube Unit Support Arm Temporarily Connecting Line PowerPreinstalling the Tube Unit Collimator Combination Laying the Collimator Cables Installing the Image IntensifierTo lay cables in the unit, 7 meters are required Laying the High Voltage CablesPage Laying the I.I. Cable Making the Power Connection through the GeneratorInstalling the Measuring Chamber Installing the Tilt Angle Display- Error Display Installing the Grid Replacing the GridInstalling the Monitor Support Arm Option Installing the Cover PanelsSealing the Table Frame Cover Panel Installing the Mount for the Flush BowlTube Unit Support Arm AdjustmentCentral Beam Center Central Beam Center of BuckyLengthwise to the tabletop, for this Movement Path Potentiometer, Tabletop longitudinal Bucky Cassette Tray Movement Path Potentiometer Movement Path Potentiometer, Tabletop transverseI.I. Carriage System Potentiometer Potentiometer 2 Table Tilt Movement Path Potentiometer 1 Table Tilt Movement PathTabletop Transverse Safety Switch Not configured Tabletop Longitudinal Safety Switch13 I.I. Carriage Movement Path Safety Switch Bucky Movement Path Safety SwitchTable Up Movement Path Switch Strike Plate Table Down Movement Path Switch Strike Plate17 +88 Tilt Movement Safety Switch 16 -20 Tilt Movement Safety SwitchSpindle Nut Safety Limit Switch Tabletop longitudinal Belt Tension Accessory Sensor SwitchesRaise-Lower Tabletop Belt Tension Cassette Carriage Drive Belt Tension Equipment Operation in the Service ModeProcedure Setting ParametersStartup Adjusting the AxesCollimator Basic Setting Cassette Format Setting the Collimator to the Cassette and I.I. FormatFormat Saving the Parameters in the PC Setup Parameters Electronic Adjustment ParametersTabletop long. Store yes/no 1/0 Mechanical and Electrical Checks Technical MaintenancePreparations Page Function Check Page Spare Parts, Overview 176Spare Parts, Unit Column Right-handed, Left-handed Versions 41/43 40/41 /10Spare Parts, Table Frame Tabletop, Right-handed Version 122 125 11 119 120 121 151Spare Parts, Table Frame Tabletop, Left-handed Version 128 135 185 136213 209 202 203 191 192 197 194 193 198 201 207 / 210 Spare Parts, Tube Unit Support Right-handed Version 193 191Spare Parts, Tube Unit Support Left-handed Version 209 207 / 210249 155 156 Spare Parts, AccessoriesPos Designation Spare Parts ListPos Designation Pos Designation Pos Designation Pos Designation Error Cause Corrective Measure Number TroubleshootingPage Version Update Board ReplacementMaintenance Verification Location of Identification Labels Labeling Overview of Labels Max kg/ 66 lb
Top Page Image Contents