Hobart Welding Products OM-1594 Adjusting Contact Tip Position, Opening Top Cover Of XR-Edge Gun

Page 24

4-9. Adjusting Contact Tip Position

XR Edge Gun

3

3

4

 

2

 

 

2

1

1

Water-Cooled Model

Air-Cooled Model

Pistol Grip Gun

1Contact Tip

2Nozzle

Adjusting barrel changes contact tip location from 1/16 in (1.6 mm) out beyond end of nozzle to 1/4 in (6.3 mm) inside nozzle.

3Nozzle Adapter Lock Nut

4Nozzle Adapter

To change contact tip location, loos- en nozzle adapter lock nut, and turn nozzle adapter. Tighten nozzle adapter lock nut.

5Jam Nut

6Barrel

To change contact tip location, loos- en jam nut, and turn barrel. Tighten jam nut.

5

6

5

2

2

1

1

6

Water-Cooled Model

Air-Cooled Model

4-10. Opening Top Cover Of XR-Edge Gun

1

Ref. 801 556 / 150 434 / Ref. 150 431 / Ref. 151 666-A

1 Top Cover

Squeeze sides of cover to release clips and lift up as shown.

To close cover, pivot cover closed on gun, and push cover down until clips lock tight.

Ref. 801 556

OM-1594 Page 20

Image 24
Contents OM-1594 ProcessesDescription From Hobart to You Table of Contents Electrical Diagrams Symbol Usage Marks a special safety messageArc Welding Hazards Electric Shock can killARC Rays can burn eyes and skin Welding can cause fire or explo- sionFlying Metal can injure eyes Buildup of GAS can injure or killPrincipal Safety Standards EMF Information About PacemakersSignification des symboles UN Choc É Lectrique peut tuerLES Fumé ES ET LES GAZ peuvent ê tre dangereux Identifie un message de sé curité particulierLE Soudage peut provoquer un incendie ou une explosion DES Particules Volantes peuvent blesser les yeuxLE Bruit peut affecter l’ouïe Risque D’INCENDIE OU LA Chute DE L’APPAREIL peut blesser’EMPLOI Excessif peut DES Organes Mobiles peuvent provoquer des blessuresPrincipales normes de sé curité Information sur les champs é lectromagné tiquesConsignes relatives aux stimulateurs cardiaques Disconnect input plug or power before working on machine Drive rolls can injure fingersKeep your head out of the fumes Rating Label For CE Products Symbols And Definitions SpecificationsPower DiameterDuty Cycle And Overheating Continuous Welding Minutes WeldingContinuous Welding Do not use gas pressure Above 50 psi 345 kPaAir-Cooled Feeder Connections Rear PanelAir-Cooled Gun Connections Water-Cooled Feeder Connections Water-Cooled Gun Connections Pin Plug Information Voltage Sensing Lead ConnectionsDigital Meter Display Meters/Minute Inches/MinuteAdjusting Contact Tip Position Opening Top Cover Of XR-Edge GunXR Edge Gun Pistol Grip GunInstalling Wire Spool Removing Top Cover Of Pistol Grip GunThreading Welding Wire Through Feeder 150 mm Pull and hold wire cut off end Proceed to SectionTools Needed Open tension arm Threading Welding Wire Through Gun Nonconductive Surface Feed wire to check drive rollFor XR-Edge Gun For Pistol-Grip GunAdjusting Wire Feed Starting Speed Setting Switches For Preflow And Postflow Adjusting Trigger Hold Actuation Time Trigger hold actuation time Range is from 0 to 4 secondsOperation ControlsInternal Controls Gun Controls Shielding Gas Coolant Supply For Water-Cooled Models OnlySequence Of Gas Metal Arc Welding Gmaw Continuous Or Spot Feeder Drive Assembly Maintenance Wire sizeGun Drive Assembly Maintenance For An XR-Edge Gun Post Pressure Roll w/BearingRemoving Contact Tip Adapter In XR-Edge Guns Replacing Head Tube Liner In XR-Edge GunsInsert chamfered end of liner into head tube Turn Off welding power Source and wire feeder Replacing Gun Cable LinerReplacing Or Cleaning Gun Drive Roll In Pistol-Grip Guns Changing Gun Contact TipTurn Off wire feeder and welding power source Top Cover Replacing Head Tube Liner In Pistol-Grip GunsPressure Roll Insert chamfered end of liner into head tube Tool NeededRemoving Contact Tip Adapter In Air-Cooled Pistol-Grip Guns Replacing Hub Assembly Reinstall gun coverWater Flow Switch Optional For Water-Cooled Models Turn Off WireOverload Protection Engine WeldingTroubleshooting Disconnect power before troubleshootingFilter, and clean fittings Trouble RemedyOM-1594 Electrical Diagrams 186 931-D Circuit Diagram For Gun OM-1594 Main Assembly 12 13 16 17MP1 Motor & Wire Drive Motor & Wire Drive -1 Item Panel, Front w/Components Water-Cooled Model Illustrated See FigurePanel, Front w/Components -1 Item Exploded View Of XR-Edge Gun See185 202 Barrel Assembly Of XR-Edge Gun Exploded View Of Pistol-Grip Gun 15Fig46 47 133 Dia Part Barrel Assembly Of Pistol-Grip Gun 137 Barrel ASSEMBLY, water cooled 15W & 30W models OM-1594 OM-1594 Service SupportContact your Distributor for Hobart Welding ProductsCall