Delta 36-714B instruction manual To Adjust the Table Insert

Page 12

7.Attach the blade guard and splitter assembly (G) Fig. 19 between the large washer (C) and the splitter bracket. Tighten the screw (H) with the supplied wrench. Slide the splitter as far down as it will go.

8.Fasten the rear of the blade guard and splitter bracket assembly (G) Fig. 19 to the rear splitter-mounting bracket. Align the hole (J) in the blade guard and splitter bracket with the hole in the rear splitter-mounting bracket. Insert a 5/16-18 x 5/8" carriage bolt through the hole (J). Place a 5/16" flat washer and external tooth lockwasher on the bolt and fasten with a 5/16- 18 hex nut. Tighten securely.

IMPORTANT: The splitter (G) Fig. 20 has a notch (L) cut in the top edge. This feature enables the blade guard to stay in the raised position to make blade changing easier. Raise the front of blade guard (M) until the rear edge of the blade guard slips into the notch (L) of the splitter (G). This feature only works when the table insert is removed.

9.With the blade guard (L) Fig. 21 in the raised position, attach the saw blade (K) on the arbor with the two arbor wrenches. For more instructions on changing blades, see “HOW TO ATTACH THE SAW BLADE” section in this manual.

G

C

H

Fig. 19

L

G

Fig. 21

L

G

Fig. 20

K

Fig. 22

J

Always return the guard to the "down" position before operating the saw.

Do not operate the saw without the table insert and guard in place.

10.Use a straight edge to check the alignment of the rear of the splitter (G) with the saw blade (Fig. 23). To align, loosen the screws (B) Fig. 15, align the splitter (G) with the saw blade, and tighten the screws (B) Fig. 15.

11.Lower the saw blade and install the table insert (R) Fig. 24 in the saw table.

The table insert should be level with the table surface. If an adjustment is necessary, see the section "HOW

TO ADJUST THE TABLE INSERT".

Hold on to the blade guard (L) when you install the table insert. The insert will automatically release the holding action of the splitter and lower the blade guard when it is installed in the table opening.

L

G

Fig. 23

R

Fig. 24

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents 36-714B Table of Contents Important Safety InstructionsSafety Guidelines Definitions General Safety Rules Additional Specific Safety Rules Do not CUT Metal with this SAWPower Connections Motor SpecificationsGrounding Instructions Volt Single Phase Operation Extension CordsMinimum Gauge Extension Cord Carton Contents Functional DescriptionAssembly Unpacking and CleaningHOW to Install the Drive Belt HOW to Attach the Extension Wings HOW to Install the SwitchHOW to Route the Cord HOW to Attach the Blade Guard and Splitter AssemblyTo Adjust the Table Insert HOW to Attach a SAW Blade HOW to Align the Splitter with the BladeHOW to Install the Table Insert HOW to Adjust the Table Insert HOW to Install the Tool HoldersHOW to Install the Dust Port HOW to Assemble and Operate the Miter GaugeHOW to Start and Stop the SAW HOW to Lock the Switch in the OFF PositionHOW to Adjust the 90 and 45 Positive Stops OperationHOW to Align the Blade with the Miter Slots HOW to Adjust the Blade AlignmentHOW to Remove Play in the BLADE-ADJUSTING Mechanisms Quick Operations Checklist Splitter Assembly and AlignmentBlade Guard and Splitter USE CROSS-CUTTING MiteringBevel Crosscutting Compound MiteringRipping Construct a Push StickHOW to USE a Moulding Cutterhead Bevel RippingUsing AN Accessory Dado Head Using Auxiliary Wood Facing Power Tool InstituteConstructing a Featherboard Push Stick Constructing a Push StickTroubleshooting Maintenance ServiceAccessories WarrantyLES Instructions Importantes DE Surete Mesures DE Sécurité DéfinitionsLA Proposition DE Californie Règles DE Sécurité Générales Lutilisation DE CET OutilRègles Spécifiques Additionnelles DE Sûreté Conserver CES DirectivesRaccordements Électriques Spécifications DU MoteurInstructions DE Mise À LA Terre Cordon DE Rallonge Fonctionnement Monophasé À 240 VoltsMesur Minimum DE Corde D’EXTENSION Description Fonctionnelle Contenus DE BoiteAVANT-PROPOS Assemblage Désemballage ET NettoyageFixation DE LA Scie À UN Endroit Permanent Volants DE Réglage DE LA LameInstallation DE LA Courroie Dentraînement Installation DE Linterrupteur RallongesAcheminement DU Cordon Fixation DE Lensemble PROTÈGE-LAME/COUTEAU SéparateurPage Installation DE Linsert DE Table Fixation DE LA Lame DE LA ScieAlignement DU Couteau Séparateur Avec LA Lame Installation DES PORTE-OUTILS Installation DE LA Goulotte À PoussièreRéglage DE L’INSERT DE LA Table Jauge À OngletsFonctionnement Démarrage ET Arrêt DE LE ScieVerrouiller L’INTERRUPTEUR EN Position D’ARRÊT Protection Contre LES SurchargesAlignement DES Fentes DE LA Jauge À Onglet Avec LA Lame Utilisation DU PARE-MAIN ET DU Couteau Séparateur Liste DE Contrôle Rapide Avant UtilisationET Alignement DU PARE-MAIN ET DU Couteau Séparateur » Remarque SUR LE Serrage DU Guide DE Coupe D’ONGLET TronçonnageDécoupe À L’ONGLET Tronçonnage EN BiseauSciage EN Long Tenir LES Mains Éloignées DE LA Lame DE Scie« Fabrication D’UN Poussoir » Sciage SUR LE Long EN Biseau Utilisation DE LA Fraise À MoulurerUtilisation DE LA Tête À Rainurer Accessoire Pour rainurage plus large que 200 mm 8 po de diamètreUtilisation D’UNE Planche DE Repère Fabrication D’UNE Planche EN ÉventailPoussoir Construire UN PoussoirRemplacement Gratuit DE Létiquette Depannage EntretienPièces DE Rechange Entretien ET RéparationAccessoiries GarantieInstrucciones DE Seguridad Importantes Pautas DE SEGURIDAD/DEFINICIONESGuarde Estas Instrucciones Normas Generales DE Seguridad EL USO DE Esta HerramientaNormas Específicas Adicionales DE Seguridad No Corte Metal CON Esta SierraConexiones a LA Fuente DE Alimentación Especificaciones DEL MotorInstrucciones DE Conexión a Tierra Cordones DE Extensión Cordón DE Extensión DE Calibre MínimoOperación DE UNA Sola Fase CON 240 Voltios Descripción Funcional Contenido DE CartonPrologo Ensamblaje Instalación DE LA Correa Impulsora Bases DE Extensión Instalación DEL InterruptorRecorrido DEL Cable Acople DEL Conjunto Protector DE LA Hoja Y HendedorPage Acople DE Hoja Alineación DEL Hendedor CON LA HojaInstalación DEL Inserto DE Mesa Installing the Tool Holders Ajuste DEL Inserto DE MesaInstalación DEL Orificio Para Recolección DE Polvo Calibrador DE IngleteOperación Arrancando Y Deteniendo LA SierraFijando EL Interruptor EN LA Posicion DE Apagado Protección DE SobrecargaAlineación DE LAS Ranuras DEL Calibrador CON LA Hoja USO DEL Protector DE LA Hoja Y DEL Hendedor Lista Decontrol DE Operaciones RápidasAlineación DEL Protector DE LA Hoja Y EL Hendedor Aviso Sobre LA Sujeción DEL Calibrador DE Inglete Corte TransversalCorte a Inglete Corte Transversal CON BiselCorte Longitudinal Mantenga LAS Manos Lejos DE LA Hoja DE LA SierraCorte Longitudinal CON Bisel USO DEL Cabezal Portacuchilla Para MolduraUSO DEL Inserto DE Cabezal Para Ranuras Utilización DE Revestimiento DE Madera Auxiliar Construcción DE UNA Tabla DE Canto Biselado4ODEUNESPESOR Elanchodelmaterial Acortar MenorqueConstrucción DE UNA Vara Para Empujar Utilice Madera DE 12,7 MM 1/2Localizacion DE Fallas Mantenimiento Mantenga LA Máquina LimpiaFalla EN EL Encendido Lubricación Y Protección Contra ÓxidoServicio Piezas DE RepuestoReemplazo Gratuito DE LAS Etiquetas DE Advertencia Accesorios GarantiaMantenimiento Y Reparaciones Póliza DE Garantía Identificación DelproductoExcepciones Your ACHIEVEMENT. OUR Tools

36-714B specifications

The Delta 36-714B is a powerful and versatile scroll saw designed for both amateur woodworkers and seasoned professionals. This model stands out due to its precision, durability, and user-friendly features, making it a popular choice for those who need to create intricate designs with ease.

One of the main features of the Delta 36-714B is its robust 1.3-amp motor, which provides ample power for cutting through a variety of materials, including wood and plastic. The saw operates at variable speeds, ranging from 400 to 1,750 strokes per minute, allowing users to adjust the speed according to the specific application and material thickness. This level of control is essential for creating clean, precise cuts, particularly for intricate patterns.

The Delta 36-714B comes equipped with a large 16-inch throat, providing ample space for cutting larger projects without the need for constant repositioning. The table, made of high-quality cast iron, is both sturdy and reliable, ensuring stability during operation. The table also tilts up to 45 degrees, enabling users to make bevel cuts with ease. This feature is particularly useful for creating angled cuts or for complex projects that require varying angles.

One of the standout technologies in the Delta 36-714B is its patented blade tensioning system, which allows for quick and easy blade changes without the need for additional tools. This feature not only saves time but also enhances productivity, enabling users to switch between blades suitable for different materials quickly. Additionally, the saw is designed to accept both pin-end and plain-end blades, providing versatility in blade choices depending on the desired project.

Another noteworthy characteristic is the integrated dust blower, which helps to keep the cutting line clear of debris, allowing for improved visibility and accuracy. The included LED light illuminates the cutting area, enhancing precision work, especially in low-light conditions.

Overall, the Delta 36-714B is a well-engineered scroll saw that combines power, precision, and ease of use. Its features and technologies make it an excellent choice for woodworkers looking to tackle detailed projects with confidence. Whether for hobbyists or professionals, this scroll saw proves to be a valuable addition to any workshop.
Top Page Image Contents