Delta 36-714B instruction manual Quick Operations Checklist, Blade Guard and Splitter USE

Page 17

MACHINE USE

Common sawing operations include ripping and crosscutting plus a few other standard operations. As with all power machines, a certain amount of hazard is involved with the operation and use of the machine. Using the machine with the respect and caution will considerably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or completely ignored, personal injury can result. The following information describes the safe and proper method for performing the most common sawing operations.

This instruction manual does not provide information regarding the installation of a fence system. A fence system must be installed before use of the saw. Please refer to the fence instruction manual regarding the proper installation, alignment, and operation of the fence system.

The use of attachments and accessories not recommended be Delta may result in injury.

Never operate the saw without the proper table insert for the saw blade or cutter installed.

QUICK OPERATIONS CHECKLIST

Before using the saw each time, verify the following:

1, The blade is tight.

2.The bevel angle and height lock-knobs are tight.

3.If ripping, ensure that the fence lock lever is tight and that the fence is parallel to the blade.

4.If crosscutting, ensure that the miter gauge knob is tight.

5.Proper eye, hearing, and respiratory equipment are being used.

6.The blade guard is properly attached and the anti-kickback pawls are functioning.

Failure to adhere to these common safety rules can greatly increase the likelihood of injury.

BLADE GUARD AND SPLITTER USE

The blade guard assembly provided with Delta saws (Fig. 39) must be used for all through-sawing operations. The splitter prevents the kerf from closing and binding the blade, causing kickback. The anti-kickback pawls (A) Fig. 39 prevent the workpiece and the cut-off piece from being thrown back at the operator. The plastic guard prevents dust and debris from being thrown at the operator. To use the guard properly:

1.Make sure that the splitter is aligned with the blade as described in the section “BLADE GUARD AND

SPLITTER ASSEMBLY AND ALIGNMENT.”

2.Replace or sharpen the anti-kickback pawls when they become dull.

3.Keep the guard clean for visibility and free motion.

4.Do not use solvent or lubricants on the guard. They may severely damage the plastic.

5.Use caution when feeding workpieces that may catch on the guard and cause a bind, or force the guard into the blade (such as when cutting moulding).

A

Fig. 39

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents 36-714B Safety Guidelines Definitions Table of ContentsImportant Safety Instructions General Safety Rules Do not CUT Metal with this SAW Additional Specific Safety RulesGrounding Instructions Power ConnectionsMotor Specifications Minimum Gauge Extension Cord Volt Single Phase OperationExtension Cords Functional Description Carton ContentsUnpacking and Cleaning AssemblyHOW to Install the Drive Belt HOW to Install the Switch HOW to Attach the Extension WingsHOW to Attach the Blade Guard and Splitter Assembly HOW to Route the CordTo Adjust the Table Insert HOW to Install the Table Insert HOW to Attach a SAW BladeHOW to Align the Splitter with the Blade HOW to Install the Tool Holders HOW to Adjust the Table InsertHOW to Install the Dust Port HOW to Assemble and Operate the Miter GaugeHOW to Lock the Switch in the OFF Position HOW to Start and Stop the SAWHOW to Adjust the 90 and 45 Positive Stops OperationHOW to Remove Play in the BLADE-ADJUSTING Mechanisms HOW to Align the Blade with the Miter SlotsHOW to Adjust the Blade Alignment Blade Guard and Splitter USE Quick Operations ChecklistSplitter Assembly and Alignment Mitering CROSS-CUTTINGBevel Crosscutting Compound MiteringConstruct a Push Stick RippingBevel Ripping HOW to USE a Moulding CutterheadUsing AN Accessory Dado Head Constructing a Featherboard Using Auxiliary Wood FacingPower Tool Institute Constructing a Push Stick Push StickService Troubleshooting MaintenanceWarranty AccessoriesLA Proposition DE Californie LES Instructions Importantes DE SureteMesures DE Sécurité Définitions Lutilisation DE CET Outil Règles DE Sécurité GénéralesConserver CES Directives Règles Spécifiques Additionnelles DE SûretéInstructions DE Mise À LA Terre Raccordements ÉlectriquesSpécifications DU Moteur Mesur Minimum DE Corde D’EXTENSION Cordon DE RallongeFonctionnement Monophasé À 240 Volts AVANT-PROPOS Description FonctionnelleContenus DE Boite Désemballage ET Nettoyage AssemblageFixation DE LA Scie À UN Endroit Permanent Volants DE Réglage DE LA LameInstallation DE LA Courroie Dentraînement Rallonges Installation DE LinterrupteurFixation DE Lensemble PROTÈGE-LAME/COUTEAU Séparateur Acheminement DU CordonPage Alignement DU Couteau Séparateur Avec LA Lame Installation DE Linsert DE TableFixation DE LA Lame DE LA Scie Installation DE LA Goulotte À Poussière Installation DES PORTE-OUTILSRéglage DE L’INSERT DE LA Table Jauge À OngletsDémarrage ET Arrêt DE LE Scie FonctionnementVerrouiller L’INTERRUPTEUR EN Position D’ARRÊT Protection Contre LES SurchargesAlignement DES Fentes DE LA Jauge À Onglet Avec LA Lame ET Alignement DU PARE-MAIN ET DU Couteau Séparateur » Utilisation DU PARE-MAIN ET DU Couteau SéparateurListe DE Contrôle Rapide Avant Utilisation Tronçonnage Remarque SUR LE Serrage DU Guide DE Coupe D’ONGLETDécoupe À L’ONGLET Tronçonnage EN Biseau« Fabrication D’UN Poussoir » Sciage EN LongTenir LES Mains Éloignées DE LA Lame DE Scie Utilisation DE LA Fraise À Moulurer Sciage SUR LE Long EN BiseauPour rainurage plus large que 200 mm 8 po de diamètre Utilisation DE LA Tête À Rainurer AccessoireFabrication D’UNE Planche EN Éventail Utilisation D’UNE Planche DE RepèreConstruire UN Poussoir PoussoirDepannage Entretien Remplacement Gratuit DE LétiquettePièces DE Rechange Entretien ET RéparationGarantie AccessoiriesGuarde Estas Instrucciones Instrucciones DE Seguridad ImportantesPautas DE SEGURIDAD/DEFINICIONES EL USO DE Esta Herramienta Normas Generales DE SeguridadNo Corte Metal CON Esta Sierra Normas Específicas Adicionales DE SeguridadInstrucciones DE Conexión a Tierra Conexiones a LA Fuente DE AlimentaciónEspecificaciones DEL Motor Operación DE UNA Sola Fase CON 240 Voltios Cordones DE ExtensiónCordón DE Extensión DE Calibre Mínimo Prologo Descripción FuncionalContenido DE Carton Ensamblaje Instalación DE LA Correa Impulsora Instalación DEL Interruptor Bases DE ExtensiónAcople DEL Conjunto Protector DE LA Hoja Y Hendedor Recorrido DEL CablePage Instalación DEL Inserto DE Mesa Acople DE HojaAlineación DEL Hendedor CON LA Hoja Ajuste DEL Inserto DE Mesa Installing the Tool HoldersInstalación DEL Orificio Para Recolección DE Polvo Calibrador DE IngleteArrancando Y Deteniendo LA Sierra OperaciónFijando EL Interruptor EN LA Posicion DE Apagado Protección DE SobrecargaAlineación DE LAS Ranuras DEL Calibrador CON LA Hoja Alineación DEL Protector DE LA Hoja Y EL Hendedor USO DEL Protector DE LA Hoja Y DEL HendedorLista Decontrol DE Operaciones Rápidas Corte Transversal Aviso Sobre LA Sujeción DEL Calibrador DE IngleteCorte a Inglete Corte Transversal CON BiselMantenga LAS Manos Lejos DE LA Hoja DE LA Sierra Corte LongitudinalUSO DEL Cabezal Portacuchilla Para Moldura Corte Longitudinal CON BiselUSO DEL Inserto DE Cabezal Para Ranuras Construcción DE UNA Tabla DE Canto Biselado Utilización DE Revestimiento DE Madera AuxiliarMenorque 4ODEUNESPESOR Elanchodelmaterial AcortarConstrucción DE UNA Vara Para Empujar Utilice Madera DE 12,7 MM 1/2Mantenga LA Máquina Limpia Localizacion DE Fallas MantenimientoFalla EN EL Encendido Lubricación Y Protección Contra ÓxidoReemplazo Gratuito DE LAS Etiquetas DE Advertencia ServicioPiezas DE Repuesto Mantenimiento Y Reparaciones AccesoriosGarantia Excepciones Póliza DE GarantíaIdentificación Delproducto Your ACHIEVEMENT. OUR Tools

36-714B specifications

The Delta 36-714B is a powerful and versatile scroll saw designed for both amateur woodworkers and seasoned professionals. This model stands out due to its precision, durability, and user-friendly features, making it a popular choice for those who need to create intricate designs with ease.

One of the main features of the Delta 36-714B is its robust 1.3-amp motor, which provides ample power for cutting through a variety of materials, including wood and plastic. The saw operates at variable speeds, ranging from 400 to 1,750 strokes per minute, allowing users to adjust the speed according to the specific application and material thickness. This level of control is essential for creating clean, precise cuts, particularly for intricate patterns.

The Delta 36-714B comes equipped with a large 16-inch throat, providing ample space for cutting larger projects without the need for constant repositioning. The table, made of high-quality cast iron, is both sturdy and reliable, ensuring stability during operation. The table also tilts up to 45 degrees, enabling users to make bevel cuts with ease. This feature is particularly useful for creating angled cuts or for complex projects that require varying angles.

One of the standout technologies in the Delta 36-714B is its patented blade tensioning system, which allows for quick and easy blade changes without the need for additional tools. This feature not only saves time but also enhances productivity, enabling users to switch between blades suitable for different materials quickly. Additionally, the saw is designed to accept both pin-end and plain-end blades, providing versatility in blade choices depending on the desired project.

Another noteworthy characteristic is the integrated dust blower, which helps to keep the cutting line clear of debris, allowing for improved visibility and accuracy. The included LED light illuminates the cutting area, enhancing precision work, especially in low-light conditions.

Overall, the Delta 36-714B is a well-engineered scroll saw that combines power, precision, and ease of use. Its features and technologies make it an excellent choice for woodworkers looking to tackle detailed projects with confidence. Whether for hobbyists or professionals, this scroll saw proves to be a valuable addition to any workshop.
Top Page Image Contents