Delta 36-714B instruction manual Additional Specific Safety Rules, Do not CUT Metal with this SAW

Page 4

ADDITIONAL SPECIFIC SAFETY RULES

FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.

1. DO NOT OPERATE THIS MACHINE until it is assembled and installed according to the instructions.

2.OBTAIN ADVICE FROM YOUR SUPERVISOR, instructor, or another qualified person if you are not familiar with the operation of this machine.

3.FOLLOW ALL WIRING CODES and recommended electrical connections.

4.ALWAYS USE GUARDS, SPLITTER, AND ANTI-KICKBACK PAWLS whenever possible, including through sawing. Check to see that they are in place, secured and working correctly. Test the anti-kickback pawl action before ripping by pushing the wood under the anti-kickback teeth. The teeth must prevent the wood from being thrown toward the front of the saw.

5.CUTTING THE WORKPIECE WITHOUT THE USE OF A FENCE OR MITER GAUGE IS KNOWN AS “FREEHAND” CUTTING. NEVER perform “free-hand” operations. Use either the fence or miter gauge to position and guide the workpiece.

6.HOLD THE WORKPIECE FIRMLY against the miter gauge or fence.

7.CUTTING COMPLETELY THROUGH THE WORK-PIECE IS KNOWN AS “THROUGH-SAWING”. Ripping and cross- cutting are through-sawing operations. Cutting with the grain is ripping. Use a fence or fence system for ripping. NEVER use a miter gauge for ripping. Use push sticks for ripping a narrow workpiece. Cutting across the grain is cross- cutting. Never use a fence or fence system for cross-cutting. Instead, use a miter gauge.

8.KICKBACK IS THE NATURAL TENDENCY OF THE WORKPIECE TO BE THROWN BACK AT THE OPERATOR when the workpiece initially contacts the blade or if the workpiece pinches the blade. Kickback is dangerous and can result in serious injury.

AVOID KICKBACK by:

A.keeping blade sharp and free of rust and pitch.

B.keeping rip fence parallel to the saw blade.

C.using saw blade guard and splitter for every possible operation, including all through sawing.

D.keeping splitter aligned with sawblade.

E.keeping the anti-kickback pawls in place and sharpened.

F.pushing the workpiece past the saw blade prior to release.

G.never ripping a workpiece that is twisted or warped, or does not have a straight edge to guide along the fence.

H.using featherboards when the anti-kickback device or the guard and splitter cannot be used.

I.never sawing a large workpiece that cannot be controlled.

J.never using the fence as a guide when crosscutting.

K.never sawing a workpiece with loose knots, flaws, nails or other foreign objects.

L.never ripping a workpiece shorter than 10”.

SOME MATERIALS ARE TOO HARD AND SLIPPERY FOR THE ANTI-KICKBACK PAWLS TO BE EFFECTIVE. Plastic and compositions (like hardboard) may be cut on your saw, but be especially attentive to following proper set-up and cutting procedures to prevent any kickbacks when cutting these materials.

9.USE THE CORRECT SAWBLADE FOR THE INTENDED OPERATION. The blade must rotate toward the front of the saw. Always tighten the blade arbor nut securely. Before use, inspect the blade for cracks or missing teeth. Do not use a damaged blade.

10.NEVER USE ABRASIVE WHEELS on this saw.

11.DO NOT CUT METAL WITH THIS SAW.

12.REMOVE CUT-OFF PIECES AND SCRAPS from the table before starting the saw. The vibration of the machine may cause them to move into the saw blade and be thrown out.

13.CUT-OFF PIECES CAN BE THROWN BACK AT THE OPERATOR. For large cut-off pieces, use a push stick to push the piece past the blade and off the back of the saw table. Do not reach across sawblade. Be careful that small pieces do not contact the blade.

14.NEVER ATTEMPT TO FREE A STALLED SAW BLADE WITHOUT FIRST TURNING THE MACHINE OFF. If a workpiece or cut-off piece becomes trapped inside the guard, turn saw off and wait for blade to stop before lifting the guard and removing the piece.

15.NEVER START THE MACHINE with the workpiece against the blade.

16.NEVER run the workpiece between the fence and a moulding cutterhead.

17.KEEP ARMS, HANDS, AND FINGERS away from the blade. Use a push stick to push small workpieces through the saw. A push stick is a small wooden stick, usually homemade, that should be used whenever the size or shape of the workpiece would cause you to place your hands within six inches of the blade. See “CONSTRUCTING A PUSH STICK” in the back of this manual for guidance on making your own.

18.AVOID AWKWARD OPERATIONS AND HAND POSITIONS where a sudden slip could cause a hand to move into the blade.

19.NEVER have any part of your body in line with the path of the saw blade.

20.NEVER REACH AROUND or over the saw blade.

21.PROPERLY SUPPORT LONG (3 feet or longer) OR WIDE (36” or wider) WORKPIECES. If extension tables wider than 24” are attached to the saw, bolt the saw stand to the floor, or use a sturdy outrigger support to prevent tipping.

22.PREVENT MOTION OF THE SAW WHILE IN USE. If the mobility kit is installed, lower the foot pedal and level the feet so the saw does not rock, walk, slide or tip. If necessary, secure the stand to the floor.

23.NEVER PERFORM LAYOUT, assembly or set-up work on the table/work area when the machine is running.

24.TURN THE MACHINE “OFF” AND DISCONNECT THE MACHINE from the power source before installing or removing accessories, changing the sawblade, or adjusting or changing set-ups. Lock switch in the “OFF” position when making repairs.

25.CLEAN THE TABLE/WORK AREA BEFORE LEAVING THE MACHINE. Lock the switch in the “OFF” position to prevent unauthorized use.

26.ADDITIONAL INFORMATION regarding the safe and proper operation of power tools (i.e. a safety video) is available from the Power Tool Institute, 1300 Sumner Avenue, Cleveland, OH 44115-2851 (www.powertoolinstitute.com). Information is also available from the National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201. Please refer to the American National Standards Institute ANSI 01.1 Safety Requirements for Woodworking Machines and the U.S. Department of Labor OSHA 1910.213 Regulations.

SAVE THESE INSTRUCTIONS. Refer to them often and use them to instruct others.

4

Image 4
Contents 36-714B Important Safety Instructions Table of ContentsSafety Guidelines Definitions General Safety Rules Additional Specific Safety Rules Do not CUT Metal with this SAWMotor Specifications Power ConnectionsGrounding Instructions Extension Cords Volt Single Phase OperationMinimum Gauge Extension Cord Carton Contents Functional DescriptionAssembly Unpacking and CleaningHOW to Install the Drive Belt HOW to Attach the Extension Wings HOW to Install the SwitchHOW to Route the Cord HOW to Attach the Blade Guard and Splitter AssemblyTo Adjust the Table Insert HOW to Align the Splitter with the Blade HOW to Attach a SAW BladeHOW to Install the Table Insert HOW to Adjust the Table Insert HOW to Install the Tool HoldersHOW to Install the Dust Port HOW to Assemble and Operate the Miter GaugeHOW to Start and Stop the SAW HOW to Lock the Switch in the OFF PositionHOW to Adjust the 90 and 45 Positive Stops OperationHOW to Adjust the Blade Alignment HOW to Align the Blade with the Miter SlotsHOW to Remove Play in the BLADE-ADJUSTING Mechanisms Splitter Assembly and Alignment Quick Operations ChecklistBlade Guard and Splitter USE CROSS-CUTTING MiteringBevel Crosscutting Compound MiteringRipping Construct a Push StickHOW to USE a Moulding Cutterhead Bevel RippingUsing AN Accessory Dado Head Power Tool Institute Using Auxiliary Wood FacingConstructing a Featherboard Push Stick Constructing a Push StickTroubleshooting Maintenance ServiceAccessories WarrantyMesures DE Sécurité Définitions LES Instructions Importantes DE SureteLA Proposition DE Californie Règles DE Sécurité Générales Lutilisation DE CET OutilRègles Spécifiques Additionnelles DE Sûreté Conserver CES DirectivesSpécifications DU Moteur Raccordements ÉlectriquesInstructions DE Mise À LA Terre Fonctionnement Monophasé À 240 Volts Cordon DE RallongeMesur Minimum DE Corde D’EXTENSION Contenus DE Boite Description FonctionnelleAVANT-PROPOS Assemblage Désemballage ET NettoyageFixation DE LA Scie À UN Endroit Permanent Volants DE Réglage DE LA LameInstallation DE LA Courroie Dentraînement Installation DE Linterrupteur RallongesAcheminement DU Cordon Fixation DE Lensemble PROTÈGE-LAME/COUTEAU SéparateurPage Fixation DE LA Lame DE LA Scie Installation DE Linsert DE TableAlignement DU Couteau Séparateur Avec LA Lame Installation DES PORTE-OUTILS Installation DE LA Goulotte À PoussièreRéglage DE L’INSERT DE LA Table Jauge À OngletsFonctionnement Démarrage ET Arrêt DE LE ScieVerrouiller L’INTERRUPTEUR EN Position D’ARRÊT Protection Contre LES SurchargesAlignement DES Fentes DE LA Jauge À Onglet Avec LA Lame Liste DE Contrôle Rapide Avant Utilisation Utilisation DU PARE-MAIN ET DU Couteau SéparateurET Alignement DU PARE-MAIN ET DU Couteau Séparateur » Remarque SUR LE Serrage DU Guide DE Coupe D’ONGLET TronçonnageDécoupe À L’ONGLET Tronçonnage EN BiseauTenir LES Mains Éloignées DE LA Lame DE Scie Sciage EN Long« Fabrication D’UN Poussoir » Sciage SUR LE Long EN Biseau Utilisation DE LA Fraise À MoulurerUtilisation DE LA Tête À Rainurer Accessoire Pour rainurage plus large que 200 mm 8 po de diamètreUtilisation D’UNE Planche DE Repère Fabrication D’UNE Planche EN ÉventailPoussoir Construire UN PoussoirRemplacement Gratuit DE Létiquette Depannage EntretienPièces DE Rechange Entretien ET RéparationAccessoiries GarantiePautas DE SEGURIDAD/DEFINICIONES Instrucciones DE Seguridad ImportantesGuarde Estas Instrucciones Normas Generales DE Seguridad EL USO DE Esta HerramientaNormas Específicas Adicionales DE Seguridad No Corte Metal CON Esta SierraEspecificaciones DEL Motor Conexiones a LA Fuente DE AlimentaciónInstrucciones DE Conexión a Tierra Cordón DE Extensión DE Calibre Mínimo Cordones DE ExtensiónOperación DE UNA Sola Fase CON 240 Voltios Contenido DE Carton Descripción FuncionalPrologo Ensamblaje Instalación DE LA Correa Impulsora Bases DE Extensión Instalación DEL InterruptorRecorrido DEL Cable Acople DEL Conjunto Protector DE LA Hoja Y HendedorPage Alineación DEL Hendedor CON LA Hoja Acople DE HojaInstalación DEL Inserto DE Mesa Installing the Tool Holders Ajuste DEL Inserto DE MesaInstalación DEL Orificio Para Recolección DE Polvo Calibrador DE IngleteOperación Arrancando Y Deteniendo LA SierraFijando EL Interruptor EN LA Posicion DE Apagado Protección DE SobrecargaAlineación DE LAS Ranuras DEL Calibrador CON LA Hoja Lista Decontrol DE Operaciones Rápidas USO DEL Protector DE LA Hoja Y DEL HendedorAlineación DEL Protector DE LA Hoja Y EL Hendedor Aviso Sobre LA Sujeción DEL Calibrador DE Inglete Corte TransversalCorte a Inglete Corte Transversal CON BiselCorte Longitudinal Mantenga LAS Manos Lejos DE LA Hoja DE LA SierraCorte Longitudinal CON Bisel USO DEL Cabezal Portacuchilla Para MolduraUSO DEL Inserto DE Cabezal Para Ranuras Utilización DE Revestimiento DE Madera Auxiliar Construcción DE UNA Tabla DE Canto Biselado4ODEUNESPESOR Elanchodelmaterial Acortar MenorqueConstrucción DE UNA Vara Para Empujar Utilice Madera DE 12,7 MM 1/2Localizacion DE Fallas Mantenimiento Mantenga LA Máquina LimpiaFalla EN EL Encendido Lubricación Y Protección Contra ÓxidoPiezas DE Repuesto ServicioReemplazo Gratuito DE LAS Etiquetas DE Advertencia Garantia AccesoriosMantenimiento Y Reparaciones Identificación Delproducto Póliza DE GarantíaExcepciones Your ACHIEVEMENT. OUR Tools

36-714B specifications

The Delta 36-714B is a powerful and versatile scroll saw designed for both amateur woodworkers and seasoned professionals. This model stands out due to its precision, durability, and user-friendly features, making it a popular choice for those who need to create intricate designs with ease.

One of the main features of the Delta 36-714B is its robust 1.3-amp motor, which provides ample power for cutting through a variety of materials, including wood and plastic. The saw operates at variable speeds, ranging from 400 to 1,750 strokes per minute, allowing users to adjust the speed according to the specific application and material thickness. This level of control is essential for creating clean, precise cuts, particularly for intricate patterns.

The Delta 36-714B comes equipped with a large 16-inch throat, providing ample space for cutting larger projects without the need for constant repositioning. The table, made of high-quality cast iron, is both sturdy and reliable, ensuring stability during operation. The table also tilts up to 45 degrees, enabling users to make bevel cuts with ease. This feature is particularly useful for creating angled cuts or for complex projects that require varying angles.

One of the standout technologies in the Delta 36-714B is its patented blade tensioning system, which allows for quick and easy blade changes without the need for additional tools. This feature not only saves time but also enhances productivity, enabling users to switch between blades suitable for different materials quickly. Additionally, the saw is designed to accept both pin-end and plain-end blades, providing versatility in blade choices depending on the desired project.

Another noteworthy characteristic is the integrated dust blower, which helps to keep the cutting line clear of debris, allowing for improved visibility and accuracy. The included LED light illuminates the cutting area, enhancing precision work, especially in low-light conditions.

Overall, the Delta 36-714B is a well-engineered scroll saw that combines power, precision, and ease of use. Its features and technologies make it an excellent choice for woodworkers looking to tackle detailed projects with confidence. Whether for hobbyists or professionals, this scroll saw proves to be a valuable addition to any workshop.