Delta 36-714B instruction manual HOW to Adjust the Table Insert, HOW to Install the Tool Holders

Page 14

HOW TO ADJUST THE TABLE INSERT

Disconnect the machine from the power source!

Make sure that the table insert (A) is always level with the table.

Place a straight edge (B) Fig. 29 across the table at both ends of the table insert (A).

To adjust, loosen the screw (D) Fig. 29 and turn the adjusting screws (C) Fig. 29 with the supplied hex wrench.

A

B

C

D

C

Fig. 29

HOW TO INSTALL THE TOOL HOLDERS

Disconnect the machine from the power source!

Install the fence holders (A) Fig. 30 using four (4) 1/4"-20 x 3/8" self-tapping screws.

Install the wrench hook (B) using two (2) M4 x 8mm self- tapping screws.

B

A

Fig. 30

HOW TO INSTALL THE DUST PORT

Disconnect the machine from the power source!

Attach the dust port (D) Fig. 31 using four 1/4-20 x 3/8" self-tapping screws.

D

Fig. 31

HOW TO ASSEMBLE AND OPERATE THE MITER GAUGE

Disconnect the machine from the power source!

Refer to the instruction sheet that came with your 36-946 miter gauge for assembly and operation instructions.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents 36-714B Safety Guidelines Definitions Table of ContentsImportant Safety Instructions General Safety Rules Additional Specific Safety Rules Do not CUT Metal with this SAWGrounding Instructions Power ConnectionsMotor Specifications Minimum Gauge Extension Cord Volt Single Phase OperationExtension Cords Carton Contents Functional DescriptionAssembly Unpacking and CleaningHOW to Install the Drive Belt HOW to Attach the Extension Wings HOW to Install the SwitchHOW to Route the Cord HOW to Attach the Blade Guard and Splitter AssemblyTo Adjust the Table Insert HOW to Install the Table Insert HOW to Attach a SAW BladeHOW to Align the Splitter with the Blade HOW to Install the Dust Port HOW to Adjust the Table InsertHOW to Install the Tool Holders HOW to Assemble and Operate the Miter GaugeHOW to Adjust the 90 and 45 Positive Stops HOW to Start and Stop the SAWHOW to Lock the Switch in the OFF Position OperationHOW to Remove Play in the BLADE-ADJUSTING Mechanisms HOW to Align the Blade with the Miter SlotsHOW to Adjust the Blade Alignment Blade Guard and Splitter USE Quick Operations ChecklistSplitter Assembly and Alignment Bevel Crosscutting CROSS-CUTTINGMitering Compound MiteringRipping Construct a Push StickHOW to USE a Moulding Cutterhead Bevel RippingUsing AN Accessory Dado Head Constructing a Featherboard Using Auxiliary Wood FacingPower Tool Institute Push Stick Constructing a Push StickTroubleshooting Maintenance ServiceAccessories WarrantyLA Proposition DE Californie LES Instructions Importantes DE SureteMesures DE Sécurité Définitions Règles DE Sécurité Générales Lutilisation DE CET OutilRègles Spécifiques Additionnelles DE Sûreté Conserver CES DirectivesInstructions DE Mise À LA Terre Raccordements ÉlectriquesSpécifications DU Moteur Mesur Minimum DE Corde D’EXTENSION Cordon DE RallongeFonctionnement Monophasé À 240 Volts AVANT-PROPOS Description FonctionnelleContenus DE Boite Fixation DE LA Scie À UN Endroit Permanent AssemblageDésemballage ET Nettoyage Volants DE Réglage DE LA LameInstallation DE LA Courroie Dentraînement Installation DE Linterrupteur RallongesAcheminement DU Cordon Fixation DE Lensemble PROTÈGE-LAME/COUTEAU SéparateurPage Alignement DU Couteau Séparateur Avec LA Lame Installation DE Linsert DE TableFixation DE LA Lame DE LA Scie Réglage DE L’INSERT DE LA Table Installation DES PORTE-OUTILSInstallation DE LA Goulotte À Poussière Jauge À OngletsVerrouiller L’INTERRUPTEUR EN Position D’ARRÊT FonctionnementDémarrage ET Arrêt DE LE Scie Protection Contre LES SurchargesAlignement DES Fentes DE LA Jauge À Onglet Avec LA Lame ET Alignement DU PARE-MAIN ET DU Couteau Séparateur » Utilisation DU PARE-MAIN ET DU Couteau SéparateurListe DE Contrôle Rapide Avant Utilisation Découpe À L’ONGLET Remarque SUR LE Serrage DU Guide DE Coupe D’ONGLETTronçonnage Tronçonnage EN Biseau« Fabrication D’UN Poussoir » Sciage EN LongTenir LES Mains Éloignées DE LA Lame DE Scie Sciage SUR LE Long EN Biseau Utilisation DE LA Fraise À MoulurerUtilisation DE LA Tête À Rainurer Accessoire Pour rainurage plus large que 200 mm 8 po de diamètreUtilisation D’UNE Planche DE Repère Fabrication D’UNE Planche EN ÉventailPoussoir Construire UN PoussoirPièces DE Rechange Remplacement Gratuit DE LétiquetteDepannage Entretien Entretien ET RéparationAccessoiries GarantieGuarde Estas Instrucciones Instrucciones DE Seguridad ImportantesPautas DE SEGURIDAD/DEFINICIONES Normas Generales DE Seguridad EL USO DE Esta HerramientaNormas Específicas Adicionales DE Seguridad No Corte Metal CON Esta SierraInstrucciones DE Conexión a Tierra Conexiones a LA Fuente DE AlimentaciónEspecificaciones DEL Motor Operación DE UNA Sola Fase CON 240 Voltios Cordones DE ExtensiónCordón DE Extensión DE Calibre Mínimo Prologo Descripción FuncionalContenido DE Carton Ensamblaje Instalación DE LA Correa Impulsora Bases DE Extensión Instalación DEL InterruptorRecorrido DEL Cable Acople DEL Conjunto Protector DE LA Hoja Y HendedorPage Instalación DEL Inserto DE Mesa Acople DE HojaAlineación DEL Hendedor CON LA Hoja Instalación DEL Orificio Para Recolección DE Polvo Installing the Tool HoldersAjuste DEL Inserto DE Mesa Calibrador DE IngleteFijando EL Interruptor EN LA Posicion DE Apagado OperaciónArrancando Y Deteniendo LA Sierra Protección DE SobrecargaAlineación DE LAS Ranuras DEL Calibrador CON LA Hoja Alineación DEL Protector DE LA Hoja Y EL Hendedor USO DEL Protector DE LA Hoja Y DEL HendedorLista Decontrol DE Operaciones Rápidas Corte a Inglete Aviso Sobre LA Sujeción DEL Calibrador DE IngleteCorte Transversal Corte Transversal CON BiselCorte Longitudinal Mantenga LAS Manos Lejos DE LA Hoja DE LA SierraCorte Longitudinal CON Bisel USO DEL Cabezal Portacuchilla Para MolduraUSO DEL Inserto DE Cabezal Para Ranuras Utilización DE Revestimiento DE Madera Auxiliar Construcción DE UNA Tabla DE Canto BiseladoConstrucción DE UNA Vara Para Empujar 4ODEUNESPESOR Elanchodelmaterial AcortarMenorque Utilice Madera DE 12,7 MM 1/2Falla EN EL Encendido Localizacion DE Fallas MantenimientoMantenga LA Máquina Limpia Lubricación Y Protección Contra ÓxidoReemplazo Gratuito DE LAS Etiquetas DE Advertencia ServicioPiezas DE Repuesto Mantenimiento Y Reparaciones AccesoriosGarantia Excepciones Póliza DE GarantíaIdentificación Delproducto Your ACHIEVEMENT. OUR Tools

36-714B specifications

The Delta 36-714B is a powerful and versatile scroll saw designed for both amateur woodworkers and seasoned professionals. This model stands out due to its precision, durability, and user-friendly features, making it a popular choice for those who need to create intricate designs with ease.

One of the main features of the Delta 36-714B is its robust 1.3-amp motor, which provides ample power for cutting through a variety of materials, including wood and plastic. The saw operates at variable speeds, ranging from 400 to 1,750 strokes per minute, allowing users to adjust the speed according to the specific application and material thickness. This level of control is essential for creating clean, precise cuts, particularly for intricate patterns.

The Delta 36-714B comes equipped with a large 16-inch throat, providing ample space for cutting larger projects without the need for constant repositioning. The table, made of high-quality cast iron, is both sturdy and reliable, ensuring stability during operation. The table also tilts up to 45 degrees, enabling users to make bevel cuts with ease. This feature is particularly useful for creating angled cuts or for complex projects that require varying angles.

One of the standout technologies in the Delta 36-714B is its patented blade tensioning system, which allows for quick and easy blade changes without the need for additional tools. This feature not only saves time but also enhances productivity, enabling users to switch between blades suitable for different materials quickly. Additionally, the saw is designed to accept both pin-end and plain-end blades, providing versatility in blade choices depending on the desired project.

Another noteworthy characteristic is the integrated dust blower, which helps to keep the cutting line clear of debris, allowing for improved visibility and accuracy. The included LED light illuminates the cutting area, enhancing precision work, especially in low-light conditions.

Overall, the Delta 36-714B is a well-engineered scroll saw that combines power, precision, and ease of use. Its features and technologies make it an excellent choice for woodworkers looking to tackle detailed projects with confidence. Whether for hobbyists or professionals, this scroll saw proves to be a valuable addition to any workshop.
Top Page Image Contents