Delta 36-714B instruction manual Operation, HOW to Start and Stop the SAW, Overload Protection

Page 15

OPERATION

OPERATIONAL CONTROLS AND ADJUSTMENTS

HOW TO START AND STOP THE SAW

The on/off switch is located underneath the switch shield (A) Fig. 32. To turn the saw “ON”, press the green button (B) Fig. 32 below the shield. To turn the saw “OFF”, push the switch shield (A) Fig. 32.

Make sure that the switch is in the “OFF” position before plugging in the power cord. In the event of a power failure, move the switch to the “OFF” position. An accidental start-up can cause injury.

HOW TO LOCK THE SWITCH IN THE “OFF” POSITION

IMPORTANT: When the tool is not in use, the switch should be locked in the Use a padlock (B) Fig. 33 with a 3/16" diameter shackle.

“OFF” position to prevent unauthorized use.

B

A

Fig. 32

A

B

Fig. 33

OVERLOAD PROTECTION

The saw is equipped with a circuit breaker (A) Fig. 33. If the motor shuts off or fails to start due to overloading (cutting stock too fast, using a dull blade, using the saw beyond its capacity, etc.), or low voltage, turn the saw off by pushing the switch shield (A) Fig. 32. Let the motor cool three to five minutes and push the reset button (A) Fig. 33. Start the motor.

HOW TO ADJUST THE 90° AND 45° POSITIVE STOPS

Your saw is equipped with positive stops that will quickly and accurately position the saw blade at 90° and 45° to the table. To check and adjust the positive stops:

Disconnect the machine from the power source.

1.Raise the saw blade to its highest position.

2.Set the blade at 90° to the table by turning the blade- tilting handwheel counter-clockwise as far as it will go.

3.Use a combination square (A) Fig. 34 to see if the blade is 90° to the table surface.

4.If not, turn the handwheel one turn clockwise. Loosen the set screw (B) Fig. 34 with a 5/32" hex wrench. Turn the handwheel until the blade is at 90° to the table. Tighten the set screw (F) until it bottoms.

5.Loosen the screws (E) Fig. 35, adjust the hairline indicator

(D) to point to the 0° mark on the scale, and tighten the screws (E).

6.Turn the handwheel clockwise as far as it will go and use a combination square to see if the blade is at 45° to the table.

7.If not, turn the handwheel one turn counter-clockwise. Loosen the set screw (F) Fig. 34. Turn the handwheel until the blade is 45° to the table. Tighten the set screw (F) until it bottoms.

A

C

 

 

F

B

 

 

Fig. 34

E

D

Fig. 35

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents 36-714B Table of Contents Important Safety InstructionsSafety Guidelines Definitions General Safety Rules Do not CUT Metal with this SAW Additional Specific Safety RulesPower Connections Motor SpecificationsGrounding Instructions Volt Single Phase Operation Extension CordsMinimum Gauge Extension Cord Functional Description Carton ContentsUnpacking and Cleaning AssemblyHOW to Install the Drive Belt HOW to Install the Switch HOW to Attach the Extension WingsHOW to Attach the Blade Guard and Splitter Assembly HOW to Route the CordTo Adjust the Table Insert HOW to Attach a SAW Blade HOW to Align the Splitter with the BladeHOW to Install the Table Insert HOW to Assemble and Operate the Miter Gauge HOW to Adjust the Table InsertHOW to Install the Tool Holders HOW to Install the Dust PortOperation HOW to Start and Stop the SAWHOW to Lock the Switch in the OFF Position HOW to Adjust the 90 and 45 Positive StopsHOW to Align the Blade with the Miter Slots HOW to Adjust the Blade AlignmentHOW to Remove Play in the BLADE-ADJUSTING Mechanisms Quick Operations Checklist Splitter Assembly and AlignmentBlade Guard and Splitter USE Compound Mitering CROSS-CUTTINGMitering Bevel CrosscuttingConstruct a Push Stick RippingBevel Ripping HOW to USE a Moulding CutterheadUsing AN Accessory Dado Head Using Auxiliary Wood Facing Power Tool InstituteConstructing a Featherboard Constructing a Push Stick Push StickService Troubleshooting MaintenanceWarranty AccessoriesLES Instructions Importantes DE Surete Mesures DE Sécurité DéfinitionsLA Proposition DE Californie Lutilisation DE CET Outil Règles DE Sécurité GénéralesConserver CES Directives Règles Spécifiques Additionnelles DE SûretéRaccordements Électriques Spécifications DU MoteurInstructions DE Mise À LA Terre Cordon DE Rallonge Fonctionnement Monophasé À 240 VoltsMesur Minimum DE Corde D’EXTENSION Description Fonctionnelle Contenus DE BoiteAVANT-PROPOS Volants DE Réglage DE LA Lame AssemblageDésemballage ET Nettoyage Fixation DE LA Scie À UN Endroit PermanentInstallation DE LA Courroie Dentraînement Rallonges Installation DE LinterrupteurFixation DE Lensemble PROTÈGE-LAME/COUTEAU Séparateur Acheminement DU CordonPage Installation DE Linsert DE Table Fixation DE LA Lame DE LA ScieAlignement DU Couteau Séparateur Avec LA Lame Jauge À Onglets Installation DES PORTE-OUTILSInstallation DE LA Goulotte À Poussière Réglage DE L’INSERT DE LA TableProtection Contre LES Surcharges FonctionnementDémarrage ET Arrêt DE LE Scie Verrouiller L’INTERRUPTEUR EN Position D’ARRÊTAlignement DES Fentes DE LA Jauge À Onglet Avec LA Lame Utilisation DU PARE-MAIN ET DU Couteau Séparateur Liste DE Contrôle Rapide Avant UtilisationET Alignement DU PARE-MAIN ET DU Couteau Séparateur » Tronçonnage EN Biseau Remarque SUR LE Serrage DU Guide DE Coupe D’ONGLETTronçonnage Découpe À L’ONGLETSciage EN Long Tenir LES Mains Éloignées DE LA Lame DE Scie« Fabrication D’UN Poussoir » Utilisation DE LA Fraise À Moulurer Sciage SUR LE Long EN BiseauPour rainurage plus large que 200 mm 8 po de diamètre Utilisation DE LA Tête À Rainurer AccessoireFabrication D’UNE Planche EN Éventail Utilisation D’UNE Planche DE RepèreConstruire UN Poussoir PoussoirEntretien ET Réparation Remplacement Gratuit DE LétiquetteDepannage Entretien Pièces DE RechangeGarantie AccessoiriesInstrucciones DE Seguridad Importantes Pautas DE SEGURIDAD/DEFINICIONESGuarde Estas Instrucciones EL USO DE Esta Herramienta Normas Generales DE SeguridadNo Corte Metal CON Esta Sierra Normas Específicas Adicionales DE SeguridadConexiones a LA Fuente DE Alimentación Especificaciones DEL MotorInstrucciones DE Conexión a Tierra Cordones DE Extensión Cordón DE Extensión DE Calibre MínimoOperación DE UNA Sola Fase CON 240 Voltios Descripción Funcional Contenido DE CartonPrologo Ensamblaje Instalación DE LA Correa Impulsora Instalación DEL Interruptor Bases DE ExtensiónAcople DEL Conjunto Protector DE LA Hoja Y Hendedor Recorrido DEL CablePage Acople DE Hoja Alineación DEL Hendedor CON LA HojaInstalación DEL Inserto DE Mesa Calibrador DE Inglete Installing the Tool HoldersAjuste DEL Inserto DE Mesa Instalación DEL Orificio Para Recolección DE PolvoProtección DE Sobrecarga OperaciónArrancando Y Deteniendo LA Sierra Fijando EL Interruptor EN LA Posicion DE ApagadoAlineación DE LAS Ranuras DEL Calibrador CON LA Hoja USO DEL Protector DE LA Hoja Y DEL Hendedor Lista Decontrol DE Operaciones RápidasAlineación DEL Protector DE LA Hoja Y EL Hendedor Corte Transversal CON Bisel Aviso Sobre LA Sujeción DEL Calibrador DE IngleteCorte Transversal Corte a IngleteMantenga LAS Manos Lejos DE LA Hoja DE LA Sierra Corte LongitudinalUSO DEL Cabezal Portacuchilla Para Moldura Corte Longitudinal CON BiselUSO DEL Inserto DE Cabezal Para Ranuras Construcción DE UNA Tabla DE Canto Biselado Utilización DE Revestimiento DE Madera AuxiliarUtilice Madera DE 12,7 MM 1/2 4ODEUNESPESOR Elanchodelmaterial AcortarMenorque Construcción DE UNA Vara Para EmpujarLubricación Y Protección Contra Óxido Localizacion DE Fallas MantenimientoMantenga LA Máquina Limpia Falla EN EL EncendidoServicio Piezas DE RepuestoReemplazo Gratuito DE LAS Etiquetas DE Advertencia Accesorios GarantiaMantenimiento Y Reparaciones Póliza DE Garantía Identificación DelproductoExcepciones Your ACHIEVEMENT. OUR Tools

36-714B specifications

The Delta 36-714B is a powerful and versatile scroll saw designed for both amateur woodworkers and seasoned professionals. This model stands out due to its precision, durability, and user-friendly features, making it a popular choice for those who need to create intricate designs with ease.

One of the main features of the Delta 36-714B is its robust 1.3-amp motor, which provides ample power for cutting through a variety of materials, including wood and plastic. The saw operates at variable speeds, ranging from 400 to 1,750 strokes per minute, allowing users to adjust the speed according to the specific application and material thickness. This level of control is essential for creating clean, precise cuts, particularly for intricate patterns.

The Delta 36-714B comes equipped with a large 16-inch throat, providing ample space for cutting larger projects without the need for constant repositioning. The table, made of high-quality cast iron, is both sturdy and reliable, ensuring stability during operation. The table also tilts up to 45 degrees, enabling users to make bevel cuts with ease. This feature is particularly useful for creating angled cuts or for complex projects that require varying angles.

One of the standout technologies in the Delta 36-714B is its patented blade tensioning system, which allows for quick and easy blade changes without the need for additional tools. This feature not only saves time but also enhances productivity, enabling users to switch between blades suitable for different materials quickly. Additionally, the saw is designed to accept both pin-end and plain-end blades, providing versatility in blade choices depending on the desired project.

Another noteworthy characteristic is the integrated dust blower, which helps to keep the cutting line clear of debris, allowing for improved visibility and accuracy. The included LED light illuminates the cutting area, enhancing precision work, especially in low-light conditions.

Overall, the Delta 36-714B is a well-engineered scroll saw that combines power, precision, and ease of use. Its features and technologies make it an excellent choice for woodworkers looking to tackle detailed projects with confidence. Whether for hobbyists or professionals, this scroll saw proves to be a valuable addition to any workshop.
Top Page Image Contents