Black & Decker CS1000L instruction manual General Safety Rules, Work Area

Page 2

631798-01, CS1000L Cir Saw 12/16/05 1:14 PM Page 2

GENERAL SAFETY RULES

WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

WORK AREA

Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.

Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.

Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

Double insulated tools are equipped with a polarized plug (one blade is wider than the other.) This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized

outlet. Do not change the plug in any way. Double insulation eliminates the need for the three wire grounded power cord and grounded power supply system.

Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded.

Don’t expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock.

When operating a power tool

outside, use an outdoor extension cord marked “W-A” or “W.” These cords are rated for outdoor use and reduce the risk of electric shock.

Minimum Gage for Cord Sets

Volts

 

Total Length of Cord in Feet

 

120V

 

0-25

26-50

51-100

101-150

240V

 

0-50

51-100

101-200

201-300

Ampere Rating

AWG

 

 

More

Not more

 

 

Than

Than

 

 

 

 

 

 

 

 

 

 

0 -

6

18

16

16

14

6 -

10

18

16

14

12

10-

12

16

16

14

12

12-

16

14

12

Not Recommended

PERSONAL SAFETY

Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury,

Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. Air vents cover moving parts and should be avoided.

Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents.

Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury.

Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations.

Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.

TOOL USE AND CARE

Use clamps or other practical way to secure and support the workpiece

2

Image 2
Contents 4 184mm Circular Saw With Removable Laser VEA EL Español EN LA ContraportadaGeneral Safety Rules Work AreaSpecific Safety Rules ServiceSE These Instructions Additional Safety Rules Circular Saws Causes and Operator Prevention of Kickback631798-01, CS1000L Cir Saw 12/16/05 114 PM To Reduce the Risk of Kickback Safety Instructions LasersGuard Against Kickback Motor Assembly / Adjustment SET-UPCutting Depth Adjustment Kerf Plate Adjustment Bevel Angle AdjustmentSwitch Operating InstructionsLaser Line Installing the BatteriesLaser Switch To USE Laser Line on SAW To USE Laser OFF SAWService Information MaintenanceAccessories Full TWO-YEAR Home USE WarrantySee ‘Tools-Electric’ Yellow Pages For Service & Sales Règles Générales DE Sécurité Conservez CES Directives aVE ThestructionsRègles DE Sécurité Spécifiques Utilisation ET Entretien DE L’OUTILPerformances et la sécurité de fonctionnement.V Effets DE Rebond PROTÉGEZ-VOUS DES Effets DE Rebond Directives DE Sécurité Lasers Pour Réduire LE Risque D’EFFET DE RebondRéglage DE Profondeur DE Découpe Configuration DE ’ASSEMBLAGE ET DES RéglasesMoteur Fixation ET Dépose DE LA Lame Directives D’UTILISATIONRéglage DE L’ANGLE DE Biseau InterrupteurRéglage DE LA Plaque DE Trait DE Scie Installation DES PilesRaie Laser Utilisation DU Laser Hors DE LA Scie Interrupteur DU LaserPour Utiliser LA Raie Laser SUR LA Scie Sciage Rapide Découpe EN PocheRangement DE LA CLÉ EntretienInformation SUR LES Réparations AccessoiresGraissage Garantie Complète DE Deux ANS Pour Usage RésidentielInstrucciones Seguridad PersonalMantenimiento Normas DE Seguridad EspecíficasUSO Y Cuidado DE LA Herramienta Causas DEL Retroceso Y SU Prevención POR Parte DEL Operador Conserve Estas Instrucciones Normas DE Seguridad Adicionales Sierras CircularesPara Reducir EL Riesgo DE Retroceso Instruccciones DE Seguridad Láseres Seres ENSAMBLADO/REGULACION Regulación DE LA Profundidad DE CorteInterruptor Instrucciones DE OperaciónColocación Y Remoción DE LA Hoja Regulación DE LA Placa DE CorteLínea Láser Instalación DE LAS BateríasUSO DEL Láser Fuera DE LA Sierra Interruptor DEL LáserUSO DE LA Línea Láser EN LA Sierra Lubricación Corte InternoCortes Longitudinales AccesoriosInformación DE Servicio Garantía Completa DE DOS Años Para USO EN EL HogarPUEBLA, PUE CULIACAN, SIN MONTERREY, N.LGUADALAJARA, JAL MEXICO, D.F631798-01, CS1000L Cir Saw 12/16/05 114 PM