Black & Decker FS200SD instruction manual Operational Controls and Adjustments

Page 15

MOVING THE SAW

To move the saw, grasp the side of the table opposite of the wheels. Lift the saw so that it is slightly off the floor and pull the table to the desired location as shown.

Not all floors are perfectly smooth, check both wheels each time you move the saw to ensure that they are not engaging the floor when the saw is at rest. Make sure all bolts are securely fastened.

OPERATION

OPERATIONAL CONTROLS AND ADJUSTMENTS

STARTING AND STOPPING SAW

The on/off switch (A) Fig. 29 is located on the front of the saw cabinet. To turn the saw “ON”, move the switch (A) up to the “ON” position. To turn the saw “OFF”, move the switch (A) down to the “OFF” position.

Make sure that the switch is in the “OFF” position before plugging in the power cord. In the event of a power failure, move the switch to the “OFF” position. An accidental start-up can cause injury.

LOCKING SWITCH IN THE “OFF” POSITION

IMPORTANT: When the tool is not in use, the switch should be locked in the “OFF” position to prevent unauthorized use. To lock the tool, grasp the switch toggle (B) and pull it out of the switch (Fig. 30). With the switch toggle (B) removed, the switch will not operate. However, should the switch toggle be removed while the saw is running, the machine can be turned “OFF,” but cannot be restarted without re-inserting the switch toggle (B).

A

Fig. 29

OVERLOAD PROTECTION

Your saw is equipped with a reset button (C) Fig. 30. If the motor stops or fails to start due to over-loading (cutting stock too fast, using a dull blade, using the saw beyond its capacity, etc.) or low voltage, turn the switch to the “OFF” position. Let the motor cool three to five minutes. Push the reset button (C) to reset the overload device. The motor can then be started again in the usual manner.

BLADE HEIGHT ADJUSTMENT

To adjust the height of the saw blade, turn the handwheel

(A)Fig. 31. Turning the handwheel clockwise lowers the blade and turning the handwheel counter-clockwise raises the blade.

C

B

Fig. 30

A

Fig. 31

15

Image 15

Contents Before Returning this Product for ANY FS200SD 10 Table SAWTable of Contents California Proposition Safety Guidelines DefinitionsImportant Safety Instructions General Safety RulesAdditional Specific Safety Rules Grounding Instructions Power ConnectionsFunctional Description Carton ContentsParts Elevating and Supporting Surfaces for a SAW with no Stand AssemblyUnpacking and Cleaning Assembly Tools RequiredMiter Gauge Attaching Miter Gauge HolderAssembling Stand Attaching the BAGSAW to Stand Attaching Blade Guard and Splitter Assembly Attaching Blade Height Adjusting HandwheelOn the screw L Fig Assembling RIP Fence Operation Operational Controls and AdjustmentsBlade Tilt Adjustment 45 Degree Positive Stop AdjustmentsTo Adjust Positive Stop AT 45 Degrees Table Insert Adjustment RIP Fence Operation AdjustmentsAdjusting Blade Parallel to Miter Gauge Slots Miter Gauge Operation AdjustmentsMachine USE Changing the BladeCROSS-CUTTING Ripping Never USE the Fence AS a CUT-OFF Gage When CROSS-CUTTINGUsing Auxiliary Wood Facing on RIP Fence Accessory Dado CutterheadGuard Removed for CLARITY. Always USE the Guard Page Constructing a Push Stick Push StickConstructing a Featherboard WHAT’S WRONG? What to DO… TroubleshootingWarranty MaintenanceAccessories ServiceScie Circulaire À Table DE 254 MM 10 PO FS200SD Lignes Directrices EN Matière DE Sécurité Définitions Proposition 65 DE LA CalifornieConserver CES Directives Directives DE Sécurité Importantes Règles Générales DE SécuritéPour Éviter L’EFFET DE Rebond Règles DE Sécurité Spécifiques SupplémentairesDirectives DE Mise À LA Terre Connexions ÉlectriquesIntroduction Description FonctionnelleContenu DU Carton Rallonges ÉlectriquesSurfaces DE Levage ET DE Support Pour UNE Scie Sans Socle AssemblageDésemballage ET Nettoyage Outils Nécessaires Pour L’ASSEMBLAGEFixation DU SAC Fixation DU PORTE-JAUGE À OngletJauge À Onglet Assemblage DU SocleFonctionnement Commandes ET Réglages OpérationnelsUtilisation ET Réglages DU Guide Longitudinal Réglage DE LA Hauteur DE LA LameRéglage DE L’INCLINAISON DE LA Lame Réglages DES Butées Fixes À 90 ET 45 DegrésTronçonnage Utilisation DE LA MachineUtilisation ET Réglages DE LA Jauge À Onglet Changement DE LA LameUtiliser LE Dispositif DE Protection Sciage EN Long« Fabrication DUN Poussoir » Fraise Accessoire À RainurerDépannage EntretienFabrication D’UNE Planche EN Éventail Accessoires Sierra DE Banco FS200SD Proposición DE California Pautas DE SEGURIDAD/DEFINICIONESInstrucciones Importantes Sobre Seguridad Normas Generales DE SeguridadEvite EL Retroceso Reglas DE Seguridad Adicionales Para Sierra DE MesaInstrucciones DE Conexión a Tierra Conexiones a LA Fuente DE AlimentaciónCordón DE Extensión DE Calibre Mínimo Instrucciones DE FuncionamientoContenido DE Carton Cordones DE ExtensiónEL VIO Apoyo Debe SER Fijo Y Capaz DE Sostener 300 Libras EnsamblajeDesempaquetado Y Limpieza Herramientas DE Ensamblaje RequeridasSierra QUE Ensambla Ensamblado DEL Portador DE LA Escuadra DE IngletesEscuadra DE Ingletes Montaje DE LA Base DE SoporteEnsamblado DEL Volante DE Inclinacion Y Elevado DE Hoja Ensamblado DEL Ensamblaje DE Protector DE Hoya Y HendidorEnsamblado DE LA Guia DE Corte a LO Largo Controles Y Ajustes Operacionales OperaciónFuncionamiento Y Ajustes DE LA Guia DE Corte a LO Largo Ajuste DEL Inserto Para MesaFuncionamiento Y Ajustes DE LA Escuadra DE Ingletes Realización DE Cortes AL Hilo Utilizar LA MaquinaCambio DE LA Hoja Realización DE Cortes TransversalesPalo DE Empujar Fresa DE Ranurar AccesoriaConstrucción DE UNA Tabla DE Canto Biselado Construcción DE UN Palo DE EmpujarDetección DE Problemas Mantenga LA Máquina LimpiaFalla EN EL Encendido Para Otras Localidades Llame AL 55 5326 RéparationPage