Black & Decker FS200SD instruction manual Machine USE, Changing the Blade, Cross-Cutting

Page 19

CHANGING THE BLADE

DISCONNECT THE MACHINE FROM THE POWER SOURCE. USE ONLY 10" DIAMETER SAW BLADES RATED FOR 4700 RPM OR HIGHER. USE ONLY SAW BLADES WITH 5/8" ARBOR HOLES.

1.NOTE: One 7/8" wrench is supplied with the saw for changing the saw blade.

2.Remove table insert (A) Fig. 41, and raise saw blade

(F) to its maximum height.

3.To remove blade, place the wrench (D) on the flats of the arbor nut (C) to keep the arbor from turning. Place a piece of wood (B) flat on the table against the blade so that a tooth of the blade can “grab” the wood to keep the blade from turning. Use wrench to turn the arbor nut toward the front of the saw. Remove arbor nut, blade flange (E), and saw blade.

4.Assemble the new blade, making certain the teeth point down at the front of the saw table, and assemble outside blade flange and arbor nut. Using the piece of wood (B) to keep the blade from turning, tighten arbor nut by turning wrench (D) toward the rear of the saw.

5.Replace table insert.

F

D

E

B

 

C

 

 

 

 

A

Fig. 41

MACHINE USE

Common sawing operations include ripping and crosscutting plus a few other standard operations of a fundamental nature. As with all power machines, there is a certain amount of hazard involved with the operation and use of the machine. Using the machine with the respect and caution demanded as far as safety precautions are concerned, will considerably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or completely ignored, personal injury to the operator can result. The following information describes the safe and proper method for performing the most common sawing operations.

THE USE OF ATTACHMENTS AND ACCESSORIES NOT RECOMMENDED MAY RESULT IN THE RISK OF INJURY TO THE USER OR OTHERS.

CROSS-CUTTING

Cross-cutting requires the use of the miter gage to position and guide the work. Place the work against the miter gage and advance both the gage and work toward the saw blade, as shown in Fig. 42. The miter gage may be used in either table slot. When bevel cutting (blade tilted), use the table groove that does not cause interference of your hand or miter gage with the saw blade guard.

Start the cut slowly and hold the work firmly against the miter gage and the table.

ONE OF THE RULES IN RUNNING A SAW IS THAT YOU NEVER HANG ONTO OR TOUCH THE PART OF THE WORKPIECE THAT WILL BE CUT OFF.

Hold the supported piece, not the free piece that is cut off. The feed in cross-cutting continues until the work is cut in two, and the miter gage and work are pulled back to the starting point. Before pulling the work back, it is good practice to give the work a little sideways shift to move the work slightly away from the saw blade. Never pick up any short length of free work from the table while the saw is running. Never touch a cut-off piece unless it is at least a foot long.

Fig. 42

For added safety and convenience the miter gage (A) can be fitted with an auxiliary wood-facing (B), as shown in Fig. 42A, that should be at least 1 inch higher than the maximum depth of cut, and should extend out 12 inches or more to one side or the other depending on which miter gage slot is being used. This auxiliary wood-facing

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents
Before Returning this Product for ANY FS200SD 10 Table SAWTable of Contents California Proposition Safety Guidelines DefinitionsImportant Safety Instructions General Safety RulesAdditional Specific Safety Rules Grounding Instructions Power ConnectionsFunctional Description Carton ContentsParts Elevating and Supporting Surfaces for a SAW with no Stand AssemblyUnpacking and Cleaning Assembly Tools RequiredMiter Gauge Attaching Miter Gauge HolderAttaching the BAG Assembling StandSAW to Stand Attaching Blade Guard and Splitter Assembly Attaching Blade Height Adjusting HandwheelOn the screw L Fig Assembling RIP Fence Operation Operational Controls and Adjustments45 Degree Positive Stop Adjustments Blade Tilt AdjustmentTo Adjust Positive Stop AT 45 Degrees Table Insert Adjustment RIP Fence Operation AdjustmentsAdjusting Blade Parallel to Miter Gauge Slots Miter Gauge Operation AdjustmentsChanging the Blade Machine USECROSS-CUTTING Ripping Never USE the Fence AS a CUT-OFF Gage When CROSS-CUTTINGAccessory Dado Cutterhead Using Auxiliary Wood Facing on RIP FenceGuard Removed for CLARITY. Always USE the Guard Page Constructing a Push Stick Push StickConstructing a Featherboard WHAT’S WRONG? What to DO… TroubleshootingWarranty MaintenanceAccessories ServiceScie Circulaire À Table DE 254 MM 10 PO FS200SD Proposition 65 DE LA Californie Lignes Directrices EN Matière DE Sécurité DéfinitionsConserver CES Directives Directives DE Sécurité Importantes Règles Générales DE SécuritéPour Éviter L’EFFET DE Rebond Règles DE Sécurité Spécifiques SupplémentairesDirectives DE Mise À LA Terre Connexions ÉlectriquesIntroduction Description FonctionnelleContenu DU Carton Rallonges ÉlectriquesSurfaces DE Levage ET DE Support Pour UNE Scie Sans Socle AssemblageDésemballage ET Nettoyage Outils Nécessaires Pour L’ASSEMBLAGEFixation DU SAC Fixation DU PORTE-JAUGE À OngletJauge À Onglet Assemblage DU SocleFonctionnement Commandes ET Réglages OpérationnelsUtilisation ET Réglages DU Guide Longitudinal Réglage DE LA Hauteur DE LA LameRéglage DE L’INCLINAISON DE LA Lame Réglages DES Butées Fixes À 90 ET 45 DegrésTronçonnage Utilisation DE LA MachineUtilisation ET Réglages DE LA Jauge À Onglet Changement DE LA LameUtiliser LE Dispositif DE Protection Sciage EN Long« Fabrication DUN Poussoir » Fraise Accessoire À RainurerEntretien DépannageFabrication D’UNE Planche EN Éventail Accessoires Sierra DE Banco FS200SD Proposición DE California Pautas DE SEGURIDAD/DEFINICIONESInstrucciones Importantes Sobre Seguridad Normas Generales DE SeguridadEvite EL Retroceso Reglas DE Seguridad Adicionales Para Sierra DE MesaInstrucciones DE Conexión a Tierra Conexiones a LA Fuente DE AlimentaciónCordón DE Extensión DE Calibre Mínimo Instrucciones DE FuncionamientoContenido DE Carton Cordones DE ExtensiónEL VIO Apoyo Debe SER Fijo Y Capaz DE Sostener 300 Libras EnsamblajeDesempaquetado Y Limpieza Herramientas DE Ensamblaje RequeridasSierra QUE Ensambla Ensamblado DEL Portador DE LA Escuadra DE IngletesEscuadra DE Ingletes Montaje DE LA Base DE SoporteEnsamblado DEL Ensamblaje DE Protector DE Hoya Y Hendidor Ensamblado DEL Volante DE Inclinacion Y Elevado DE HojaEnsamblado DE LA Guia DE Corte a LO Largo Controles Y Ajustes Operacionales OperaciónAjuste DEL Inserto Para Mesa Funcionamiento Y Ajustes DE LA Guia DE Corte a LO LargoFuncionamiento Y Ajustes DE LA Escuadra DE Ingletes Realización DE Cortes AL Hilo Utilizar LA MaquinaCambio DE LA Hoja Realización DE Cortes TransversalesPalo DE Empujar Fresa DE Ranurar AccesoriaConstrucción DE UNA Tabla DE Canto Biselado Construcción DE UN Palo DE EmpujarMantenga LA Máquina Limpia Detección DE ProblemasFalla EN EL Encendido Para Otras Localidades Llame AL 55 5326 RéparationPage
Top Page Image Contents