Graco 16N656, 16H960, 16N655, 16N927, 16N654 important safety instructions Skin Injection Hazard

Page 4

Warnings

WARNING

SKIN INJECTION HAZARD

High-pressure spray is able to inject toxins into the body and cause serious bodily injury. In the event that injection occurs, get immediate surgical treatment.

Do not aim the sprayer at, or spray any person or animal.

Keep hands and other body parts away from the discharge. For example, do not try to stop leaks with any part of the body.

Always engage the trigger lock when not spraying. Verify the trigger lock is functioning properly.

Always use the spray tip guard. Do not spray without spray tip guard in place.

Use caution when cleaning and changing spray tips. In the case where the spray tip clogs while spraying, follow the Pressure Relief Procedure for relieving the pressure before reversing or removing the spray tip to clean.

Do not leave the unit energized or under pressure while unattended. When the unit is not in use, follow the Pressure Relief Procedure and engage the trigger lock.

Check parts for signs of damage. Replace any damaged parts with genuine Graco parts.

This system is capable of producing 4000 psi. Use replacement parts or accessories that are rated a min- imum of 4000 psi.

Do not carry the sprayer with a finger on the trigger.

Verify that all connections are secure before operating the unit.

Know how to stop the unit and bleed pressure quickly. Be thoroughly familiar with the controls.

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

Disconnect the battery before servicing.

Always wear appropriate gloves, eye protection, and a respirator or mask when painting.

Do not operate or spray near children. Keep children away from equipment at all times.

Do not overreach or stand on an unstable support. Keep effective footing and balance at all times.

Stay alert and watch what you are doing.

Do not operate the unit when fatigued or under the influence of drugs or alcohol.

Use only in dry locations. Do not expose to water or rain.

Use in well-lit areas.

Always replace cracked, broken or missing parts immediately with genuine Graco parts. See Parts List, page 23.

BATTERY HAZARD

The battery may leak, explode, cause burns, or cause an explosion if mishandled. Contents of an open battery can cause severe irritation and/or chemical burns. If on skin, wash with soap and water. If in eyes, flush with water for at least 15 minutes and seek immediate medical attention.

Replace battery only in a well-ventilated area and away from flammable or combustible materials; includ- ing paints and solvents.

When battery is not in use, keep it away from metal objects like keys, nails, screws or other metal objects that can short circuit the battery terminals.

Do not throw into fire.

Charge only with Graco-approved charger as listed in this manual.

Do not store at temperatures below 32° or above 113° F (0° to 45° C).

Do not use at temperatures below 40° or above 90° F (4° to 32° C).

Do not expose battery to water or rain.

Do not disassemble, crush, or penetrate the battery.

Do not charge a battery that is cracked or damaged.

Follow local ordinances and/or regulations for disposal.

4

3A2308C

Image 4
Contents Protective Coating Hand-Held Paint Sprayer 3A2308C ModelTable of Contents Grounding Instructions Skin Injection Hazard Charger Electric SHOCK, Fire and Explosion Hazard Component Identification DescriptionCharger Status Indicator Lights Charging the BatteryOperation Sprayer Status Indicator Trigger Locked Common ProceduresTrigger Unlocked red ring is visible Adjusting Pressure Ti19655a Ti19656a Ti19654a Ti19653a Starting a New Job SetupSee Grounding Instructions, Install/Service Filter if needed Perform Pressure Relief Procedure,Install Tip/Guard Assembly if not installed Filling and Installing CupSetting Pressure Priming PumpTi19655a Ti19656a Ti19654a Ti19653a Getting Started with Basic Techniques Triggering SprayerAiming Sprayer Pulsating MaterialUnclogging Spray Tip/Guard Assembly Shutdown and Cleaning Flushing SprayerRemove cup and properly dispose contaminated fluid Cleaning Sprayer Exterior StorageParts Parts List Part Description QtyTroubleshooting Install/Service Filter,Removed. See Install/Service Filter Job or Refilling the Cup,See Charging the Battery, Spray Pattern Diagnostics See Shutdown and Cleaning, Repair Inlet ValveOutlet Valve Pressure Control Knob Pump Module/Drive Module Pump Rebuild Kit Clamshell Route wires from motor down the handle Motor/Control Board Replacement Kit Ti19632a Ti19641a Switch Assembly Install trigger lock over trigger with o-ring facing out Gear Replacement Ti19857a Ti19860a FCC Declaration for Battery Charger Technical DataMetric 3A2308C 3A2308C Graco Standard Warranty Graco Information