Graco Inc 244581, 309293K, 244582 important safety instructions Fluid Regulator Kit

Page 15

245944 Fluid Regulator Kit

To add a fluid regulator to the Graco isolation system, order Part No. 245944. See page 68 for the kit parts list.

1.Discharge the system voltage (page 20).

2.Relieve the pressure (page 20).

3.Open the isolated enclosure door.

4.Remove the 1/4 OD tube (A1) from the pump air inlet; see the tubing diagram on page 64.

5.Remove the waterborne fluid hose from the pump fluid outlet fitting (231) and remove the fitting.

6.Unscrew the two pump mounting screws (S, FIG. 12.) and remove the pump from the isolation enclo- sure.

7.Remove the back of the control box (258).

8.Remove tube (A2) from elbow (282) at the air mani- fold; see page 64. Install the Y fitting (506) in the elbow. Install tubes (A2) and (507) into the Y fitting. Route the tube (507) into the cabinet.

9.Replace the back of the control box (258).

10.Assemble the fluid regulator kit as shown in FIG. 12..

11.Reinstall the pump in the isolation enclosure. Use the two mounting holes to the left of the holes used previously, to allow clearance for the fluid regulator.

12.Connect tube (A1) to the air inlet of fluid regulator (504). Connect tube (507) to the pump air inlet.

13.Connect the waterborne fluid hose to the fluid regu- lator outlet fitting (501).

14.Return the system to service.

The cabinet air regulator and gauge (216, 217) will now operate the air piloted fluid regulator (504). The pump will now operate at the inlet air pressure.

Installation

Connect to	Connect
elbow (282)	Connect	Tube A1
inside control	waterborne	Tube A1
box (258)	fluid hose here

506	501
507	504

502

	Connect	505
	Connect
	tube A2	503
	here	503
	here

S

TI2149A

Fig. 12. Fluid Regulator Kit

309293K

15

Image 15

Contents Instructions/Parts List Table of Contents Gun Model Description List of ModelsFM Approved EN 50059 CompliantElectric Shock Hazard SymbolsToxic Fluid Hazard Fire and Explosion HazardPressurized Equipment Hazard Equipment Misuse HazardIntroduction How the Electrostatic Air Spray Gun WorksSpraying Waterborne Fluids Electrostatically Gun Overview Gun OverviewInstallation System Requirements Install the SystemFire, Explosion, and Electric Shock Hazard Typical Installation PRO Xs Waterborne System Key Connect the Waterborne Fluid Hose Ventilate the Spray BoothConnect the Air Line Ground the CabinetUnshielded Hose Shielded HoseUnshielded fluid connection Waterborne Hose Dimensions At Graco WB100 EnclosureAgitator Kit Agitator KitFluid Regulator Kit Fluid Regulator KitSelect a Fluid Nozzle and Air Cap Fluid NozzlesAir Caps Grounding Check Gun Grounding Check Electrical GroundingOperating Checklist Relief Procedure onOperation Turn off the main air supply valve B Adjust the Spray Pattern Fill the Fluid SupplyFire and Explosion Hazard Fully open the fluid adjustment valve Air Hose Length Air Regulator Setting Ft m Psi MPa, bar Air Regulator SettingsWhen you finish spraying, perform the Shutdown procedure on Low Voltage Adjustment Smart Guns Only Low Voltage AdjustmentShutdown Flush the Spray Gun MaintenanceDo not immerse the gun in fluid Daily Care and CleaningMaintenance Equipment Needed Clean the Air Cap and Fluid NozzleProcedure Grease Door Latch ThreadsTest Gun Resistance Electrical TestsTest Power Supply Resistance Test Power Supply ResistanceElectrode Test Electrode ResistanceTest Cylinder Resistance Test Ground Strip ResistanceWaterborne Fluid Hose TroubleshootingVoltage Loss Troubleshooting Spray GunTests Visual CheckTroubleshooting Spray Pattern Troubleshooting Gun Operation Troubleshooting Electrical Troubleshooting Lowing the Fluid Voltage Discharge Grounding ProcedureSee Test Gun Resistance on 18 and Test Gun Resistance See Check Electrical Grounding onRepair Prepare the Gun for ServiceAir Cap/Nozzle Replacement Electrode Replacement Electrode ReplacementFluid Packing Removal Fluid Packing RemovalPacking Rod Packing Rod RepairBarrel Removal Barrel InstallationPower Supply Power Supply Removal and ReplacementTurbine Alternator Removal and Replacement Fan Air Adjustment Valve Fan Air Adjustment Valve RepairAir Valve Repair Fluid Adjustment Valve RepairES ON/OFF Valve Repair Atomizing Air Restrictor Valve Removal and ReplacementParts Ref. No Alternator 19a 19b Description Qty Hook 51 Ref 19a TI1487A Ti1601a Description Qty SWITCH, ES HI/LO TI2138a Plate DescriptionQty Code Length Description In. mm Tubing and Wiring ChartTubing and Wiring Diagrams Detail of Door Interlock SwitchDetail of Control Box Accessories Air Line AccessoriesFluid Line Accessories Miscellaneous Accessories Gun Accessories402 407 401 406 403 408 404 406 Ref Part No Agitator Accessory Kit items506 507 502 505 503 Part No Fluid Regulator Accessory Kit itemsTechnical Data CategoryData Graco Standard Warranty Graco InformationToll Free