Icvc Alarm Codes, Failure to Stop | Carrier 19XRV manual

Table 5 — ICVC Alarm Codes

CHILLER PROTECTIVE LIMIT FAULTS

ICVC FAULT	PRIMARY	SECONDARY	PRIMARY CAUSE	ADDITIONAL CAUSE/REMEDY
STATE	MESSAGE	MESSAGE	PRIMARY CAUSE	ADDITIONAL CAUSE/REMEDY
STATE	MESSAGE	MESSAGE
200	PROTECTIVE LIMIT	RECTIFIER POWER	200→Rectifier Power Fault:	Malfunction within VFD Power Module.
		FAULT	Check VFD Status.	Call Carrier Service.
201	PROTECTIVE LIMIT	INVERTER POWER FAULT	201→Inverter Power Fault:	Malfunction within VFD Power Module.
			Check VFD Status.	Call Carrier Service.
202	PROTECTIVE LIMIT	MOTOR AMPS NOT	202→Motor Amps Not	Check main circuit breaker for trip. Increase
		SENSED	Sensed — Average Load	Current % Imbalance in VFD_CONF screen.
			Current [VALUE].
203	FAILURE TO START	MOTOR ACCELERATION	203→Motor Acceleration Fault	Check that inlet guide vanes are fully closed at
		FAULT	— Average Load Current	start-up.
			[VALUE].	Check Motor Rated Load Amps in VFD_CONF
				screen. Reduce unit pressure if possible.
204	FAILURE TO STOP	VFD SHUTDOWN FAULT	204→VFD Shutdown Fault:	VFD Circuit Board malfunction.
			Check Inverter Power Unit.	Call Carrier Service.
205	PROTECTIVE LIMIT	HIGH DC BUS VOLTAGE	205→High DC Bus Voltage:	Verify phase to phase and phase to ground line
			[VALUE] exceeded limit of	voltage. Monitor AC line for high transient volt-
			[LIMIT]*.	age conditions. VFD Circuit Board malfunction.
				Call Carrier Service.
206	PROTECTIVE LIMIT	VFD FAULT	206→VFD Fault Code:	See VFD Fault Code description and corrective
			[VALUE]; Check VFD Fault	action.
			Code List.
207	PROTECTIVE LIMIT	HIGH CONDENSER	207→High Cond Pressure	Check Compressor Discharge High Pressure
		PRESSURE	trip. [VALUE] exceeded Switch	switch wiring and accuracy.
			Trippoint.	Check for high condenser water temperatures,
				low water flow, fouled tubes.
				Check for division plate/gasket bypass.
				Check for noncondensables in refrigerant.
208	PROTECTIVE LIMIT	EXCESSIVE MOTOR	208→Percent Load Current	Check Motor Rated Load Amps in VFD_CONF
		AMPS	[VALUE] exceeded limit of	screen. Percent Load Current > 110%.
			[LIMIT]*.	Check Motor Rated Load Amps setting.
209	PROTECTIVE LIMIT	LINE CURRENT	209→Line Current Imbal-	Check phase to phase and phase to ground
		IMBALANCE	ance: Check VFD Fault His-	power distribution bus voltage.
			tory for Values.	Check Line Current % Imbalance in VFD_CONF
				screen. Consult power company.
210	PROTECTIVE LIMIT	LINE VOLTAGE DROPOUT	210→Single Cycle Line Volt-	Temporary loss of voltage. Disable Single Cycle
			age Dropout.	Dropout in VFD_CONF screen.
211	PROTECTIVE LIMIT	HIGH LINE VOLTAGE	211→High Percent Line Volt-	Check phase to phase and phase to ground dis-
			age [VALUE].	tribution bus voltage. Consult power company.
212	PROTECTIVE LIMIT	LOW LINE VOLTAGE	212→Low Percent Line Volt-	Check phase to phase and phase to ground dis-
			age [VALUE].	tribution bus voltage. Consult power company.
213	PROTECTIVE LIMIT	VFD MODULE RESET	213→VFD Module Power-On	Temporary loss of VFD control voltage. Check
			Reset When Running.	VFD control power breaker, transformer and
				fuses.
214	PROTECTIVE LIMIT	POWER LOSS	214→Control Power Loss	Check phase to phase and phase to ground dis-
			When Running.	tribution bus voltage.
				Check VFD fuses.
				Check 24 vac power supply to ICVC.
				Consult power company.
215	PROTECTIVE LIMIT	LOW DC BUS VOLTAGE	215→Low DC Bus Voltage:	Verify phase-to-phase and phase-to-ground line
			[VALUE] exceeded limit of	voltage. VFD Circuit Board malfunction.
			[LIMIT]*.	Call Carrier Service.
216	PROTECTIVE LIMIT	LINE VOLTAGE	216→Line Voltage Imbal-	Check phase-to-phase and phase-to-ground
		IMBALANCE	ance. Check VFD Fault His-	distribution bus voltage. Increase Line Voltage
			tory for Values.	% Imbalance in VFD_CONF screen.
217	PROTECTIVE LIMIT	MOTOR OVERLOAD TRIP	217→Motor Overload Trip;	Any phase current > 106% Rated Load Amps.
			Check VFD configurations.	Can result from significant load side current
				imbalance when running at full load.
				Check entering condenser water temperature
				and water flow rate.
				Check Motor Rated Load Amps in VFD_CONF
				screen.
218	PROTECTIVE LIMIT	VFD RECTIFIER	218→VFD Rectifier Temp	Check that VFD refrigerant isolation valves are
		OVERTEMP	Exceeded: Check Cooling and	open.
			VFD Config.	Check VFD refrigerant cooling solenoid and
				refrigerant strainer.
				Check for proper VFD cooling fan operation and
				blockage.
219	PROTECTIVE LIMIT	VFD INVERTER	219→VFD Inverter Temp	Check that VFD refrigerant isolation valves are
		OVERTEMP	Exceeded: Check Cooling and	open.
			VFD Config.	Check VFD refrigerant cooling solenoid and
				refrigerant strainer.
				Check for proper VFD cooling fan operation and
				blockage.

*[LIMIT] is shown on the ICVC as the temperature, pressure, voltage, etc., set point predefined or selected by the operator as an override, alert, or alarm condition. [VALUE] is the actual pressure, temperature, voltage, etc., at which the control tripped.

NOTE: ICVC Alarms 212-226 are declared as a result of VFD Faults.

Carrier 19XRV specifications Icvc Alarm Codes, Failure to Stop

Table 5 — ICVC Alarm Codes

CHILLER PROTECTIVE LIMIT FAULTS

PRIMARY

MESSAGE

200

201

INVERTER POWER FAULT

202

203

FAILURE TO STOP

VFD SHUTDOWN FAULT

205

[LIMIT]*.

206

VFD FAULT

207

208

[LIMIT]*.

209

210

LINE VOLTAGE DROPOUT

211

212

213

214

215

[LIMIT]*.

216

217

MOTOR OVERLOAD TRIP

218

OVERTEMP

219