SSI America 7SL instruction manual Configuration KEY Functions, Configuration Procedure

Page 14

CONFIGURATION KEY FUNCTIONS

RESET In Configuration Mode, used only to scroll back parameters

Used in Configuration Mode to decrease the parameter value.

Used in Configuration Mode to increase the parameter value.

FUNC

Monitors/Modifies parameters.

+

Loads the default parameters.

+ FUNC or + FUNC

Increases/decreases values at a higher rate when modifying parameters.

+ RESET or + RESET

Jumps to the Maximum or Minimum parameter value when modifying parameters.

CONFIGURATION PROCEDURE

1)Remove the instrument from its case.

2)Open switch V101 (See illustrations under “Prelimi- nary Hardware Settings.”)

3)Re-insert the instrument in its case.

4)Switch on power to the instrument. The upper display will show COnF.

5)Press the “” key and the lower display will show the firmware version.

Press the "FUNC" key to start the configuration proce- dure with the first parameter (L1). Press the "RESET" key to start the configuration procedure with the last parameter (d1).

The following is a complete list of parameters. The lower display will show the parameter code (L1 to d1) and the upper display will show the selection code or numerical value. No timeout is applied in the configuration mode.

L1 = Serial Interface Protocol (Skipped if option is not available.) OFF = No serial interface nbUS= Modbus

jbUS = Jbus

L2 = Serial Link Device Address (Skipped if option is not available or L1 = OFF) From 1 to 255

NOTE: The device can connect up to 31 instruments.

L3 = Baud Rate for Serial Link

(Skipped if option is not available or L1 = OFF) Set value from 600 to 19200 baud.

(19200 baud is shown on display as 1920)

L4 = Byte Format for Serial Link (Skipped if option is not available or L1 = OFF) 8E = 8 bits + even parity

8O = 8 bits + odd parity

8 = 8 bits without parity

1 4

7sl-2-00.p65

14

9/17/02, 2:40 PM

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Model 7SL HIGH/LOW Limitrol 16 DIN, Four Digit HIGH/LOW Limitrol Congratulations Guide to simple set-upTable of Contents USE Wire Suitable For 75C MinimumMounting Requirements Dimensions and Panel Cutout Measuring Inputs TC Input Wiring GuidelinesTerminal Layout RTD Linear InputRTD Input Logic Input7sl-1-00.p65 17/02, 239 PM Relay Outputs OUTSerial Interface CommonPreliminary Hardware Settings Power Line and groundingPower Supply Limitrol with RS-485 Limitrol without RS-485Configuration KEY Functions Configuration ProcedureC2 = Acknowledgment Mode R5 = Offset AdjustmentR7 = Alarm Action on Fault R1 = Input Type and Range Value R2 = Decimal Point PositionControl Output Function P2 = Alarm configuration C3 = Reset at Power-upC4 = Reset Memory = Safety Lock P3 = Alarm ActionAlarm Standby Function OFF =T1 = Timeout Selection tn10 = 10 second timeout Indicators Operating ModeNormal Display Mode ResetKey Functions in Parameter Display Mode Key Functions in Normal Display ModeParameter Display Mode Operating Parameters Error List Error MessagesError Messages Dealing with Error MessagesDefault Operating Parameters List Default ParametersLoading Default Operating Parameters Loading Default Configuration ParametersDefault Configuration Parameter List ParaSpecifications Common Mode Rejection Ratio Display Update Time RangeTemperature Drift Normal Mode Rejection RatioAlarm Function Acknowledgment ModePower-Up Mode Type of AlarmNema ReferencesCEI 70-1 IEC ENV50140Calibration Parameters Calibration ProcedureGeneral Guidelines TC Input Check ProcedureTH TC Input Final Scale Value Entering Calibration ValuesRJ. Cold Junction Compensation Check PH RTD Input Final Scale ValueRTD Check PL RTD Input Initial Scale ValueNH 5 Volt Input Final Scale Value AH Current Input Final Scale ValueCurrent Input Check Volt Input CheckUL 10 Volt Input Initial Scale Value UH 10 Volt Input Final Scale ValueMaintenance Manual Part No 7SL
Top Page Image Contents