SSI America 7SL instruction manual R1 = Input Type and Range Value R2 = Decimal Point Position

r1 =		Input Type and Range Value							r2 = Decimal Point Position
0	=	TC	J	From	-100	to	1000	°C	(Available only for linear range r1 = 15 to 22)
1	=	TC	K	From	-100	to	1370	°C	_ _ _ _ . = No decimal
2	=	TC	T	From	-200	to	400	°C	_ _ _ . _ = One decimal place
3	=	TC	E	From	-100	to	800	°C	_ _ . _ _ = Two decimal places
4	=	TC	N	From	-100	to	1400	°C	_ . _ _ _ = Three decimal places
5	=	TC	S	From	-50	to	1760	°C
6	=	TC	R	From	-50	to	1760	°C	r3 = Low Scale Range Value
7	=	TC	B	From	0	to	1820	°C	(Available only for linear range r1 = 15 to 22)
8	=	TC	L	From	-100	to	900	°C	Range: From -1999 to 9999
9	=	TC	U	From	-200	to	600	°C
10	=	TC	G	From	0	to	2300	°C	r4 = High Scale Range Value
11	=	TC	D	From	0	to	2300	°C	(Available only for linear range r1 = 15 to 22)
12	=	TC	C	From	0	to	2300	°C	Range: From -1999 to 9999
13	=	TC Plat. II		From	-100	to	1400	°C
14	=	RTD Pt 100		From	-200	to	850	°C	r5 = Offset Adjustment
15	=	Linear		From	0	to	60	mV	Range: From -500 to 500
16	=	Linear		From	12	to	60	mV	Offset value algebraically added to the measured value.
17	=	Linear		From	0	to	20	mA
18	=	Linear		From	4	to	20	mA	r6 = Time Constant for Filter on Displayed Value
19	=	Linear		From	0	to	5	V	Range: From 0 (filter OFF) to 8 seconds.
20	=	Linear		From	1	to	5	V	(First order filter with selected time constant.)
21	=	Linear		From	0	to	10	V
22	=	Linear		From	2	to	10	V	r7 = Alarm Action on Fault
23	=	TC	J	From	-150	to	1830	°F	uP = The alarm assumes an upscale reading.
24	=	TC	K	From	-150	to	2500	°F	doun = The alarm assumes a downscale reading.
25	=	TC	T	From	-330	to	750	°F
26	=	TC	E	From	-150	to	1470	°F	C1 = Type of Limit Action
27	=	TC	N	From	-150	to	2550	°F	Hi. = High limit (for heating process)
28	=	TC	S	From	-60	to	3200	°F	Lo. = Low limit (for cooling process)
29	=	TC	R	From	-60	to	3200	°F	Hi.Lo = Band limit (for special process)
30	=	TC	B	From	32	to	3300	°F
31	=	TC	L	From	-150	to	1650	°F	C2 = Acknowledgment Mode
32	=	TC	U	From	-330	to	1110	°F	O = The acknowledgment action is ignored if performed
33	=	TC	G	From	0	to	4170	°F	when setpoint is exceeded.
34	=	TC	D	From	0	to	4170	°F	I = The acknowledgment action is recognized also
35	=	TC	C	From	0	to	4170	°F	when the setpoint is exceeded. (In this case, the
36	=	TC Plat. II		From	-150	to	2550	°F	control output is instantaneously restored when
37	=	RTD Pt100		From	-330	to	1560	°F	process variable is within setpoint).
									1 5

7sl-2-00.p65 15 9/17/02, 2:40 PM