Grizzly G0454, G0453 owner manual Re-Tension V-Belts, Recommended Adjustments

Page 24

4.Push the OFF button in, then twist it clock- wise so it pops out. When the OFF button pops out, the switch is reset and ready for operation (see Figure 14).

Figure 14. Resetting the switch.

5.Verify that the machine is operating correctly by pushing the ON button.

—When operating correctly, the machine runs smoothly with little or no vibration or rubbing noises.

—Investigate and correct strange or unusual noises or vibrations before operating the machine further. Always disconnect the machine from power when investigating or correcting potential problems.

6.Press the OFF button to stop the machine.

7.WITHOUT resetting the switch, press the ON button. The machine should not start.

—If the machine does not start, the OFF but- ton safety feature is working correctly. The Test Run is complete.

—If the machine does start (with the OFF button pushed in), immediately disconnect power to the machine. The OFF button safety feature is not working correctly. This safety feature must work properly before proceeding with regular operations. Call Tech Support for help.

-22-

Re-Tension V-Belts

The final step of the setup process must be done after approximately 16 hours of operation. During this period, the V-belts will stretch and seat into the pulley grooves and need to be properly ten- sioned to avoid severely reducing the life of the V-belts. Refer to V-Beltson Page 37 for detailed instructions.

Recommended

Adjustments

For your convenience, the adjustments listed below have been performed at the factory.

However, because of the many variables involved with shipping, we recommend that you at least verify the following adjustments to ensure the best possible results from your new machine.

Step-by-step instructions for these adjustments can be found in the SERVICE section starting on Page 33.

Factory adjustments that should be verified:

•Table height chain tension (Page 39).

•Chip breaker height (Page 40).

•Pressure bar height (Page 40).

•Infeed/outfeed roller height (Page 40).

•Roller spring tension (Page 43).

•Chip deflector positioning (Page 43).

G0453/G0454 (Mfg. Since 3/08)

Image 24

Contents Model G0453/G0454 15 & 20 Mobile Planers Page Table of Contents Introduction Manual Accuracy Contact InfoMachine Description Identification ON/OFFInternal Components Machine Data Sheet Other G0454 Machine Data Sheet Knife Adjustment Jack Screws and Springs Safety Safety Instructions for MachineryUnattended OPERATION. Never leave Additional Safety Instructions for Planers Power Supply AvailabilityFull-Load Current Rating G0453 220V Circuit RequirementsGrounding Instructions Extension CordsG0453 G0454Setup Needed for SetupUnpacking Description QtyInventory Box Inventory Figure QtyG0454 Hardware and Tools not shown Cleanup Before cleaning, gather the followingBasic steps for removing rust preventative Site Considerations Assembly Lifting & Moving Base UnitTo assemble your planer Attaching magnetic switch Foot pedal and caster installed G0453/G0454 Mfg. Since 3/08 Dust Collection Test Run Check Gearbox OilRecommended Adjustments Factory adjustments that should be verifiedRe-Tension V-Belts Operations Operation OverviewPlaning Tips Workpiece InspectionWood Hardness Feed Rate Species HardnessDepth of Cut Bed Roller HeightTo adjust the bed rollers Disconnect Planer from PowerAccessories G2790 Universal Knife GrinderT20502 T20452 T20503 T20448 T20456 H0736 G8982-Roller TableMaintenance Cleaning ProtectingSchedule Lubrication Feed Roller BushingsColumns and Leadscrews Table Height Worm GearTable Height Chain & Sprockets Drive Chain & SprocketsGearbox Oil Service TroubleshootingMotor & Electrical Machine Operation Amount of snipeAdjust the height of the chip breaker or pressure bar Setting/Replacing Knives To adjust the height of the knivesTools Needed Qty Belt Tensioning Replacement To tension/replace the V-beltsPage To adjust the table height chain tension Table Height Chain TensionUsing a Rotacator Feed Rollers, Chip Breaker & Pressure Bar HeightsDist. Below Knife Edge at BDC Figure Adjustment Jam Nut Set Screw Using Wood Blocks To adjust the chip deflector gap Roller Spring TensionPositioning Chip Deflector Scale Calibration Anti-Kickback FingersTo re-position the scale Pulley Alignment To check/re-align pulleysWiring Wiring Safety InstructionsG0453 Wiring Diagram Magnetic ON/OFF SwitchG0454 Wiring Diagram NHD BTH-21Parts G0453 Headstock Parts List DescriptionG0453 Table Breakdown G0453 Columns Breakdown G0453 Cabinet Stand Breakdown G0453 Cabinet Stand Parts List G0453 Gearbox Breakdown G0453 Label Placement G0454 Headstock Breakdown G0454 Headstock Parts List PN01M HEX NUT M6-1 PSS25M SET Screw M6-1 X PB09M G0454 Table Breakdown G0454 Columns Breakdown 310G0454 Cabinet Stand Breakdown G0454 Cabinet Stand Parts List G0454 Gearbox Breakdown 538G0454 Label Placement G0453/G0454 Mfg. Since 3/08 Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty and Returns Warranty and ReturnsOrder Hours a DAY