Grizzly G0454 owner manual G0453 Label Placement

Page 58

G0453 Label Placement

19

117

116

113

114

10

451

452

115

334

446

447

REF	PART #	DESCRIPTION

10	P0453010	SPEED CHANGE LABEL
19	P0453019	BELT COVER LABEL
113	PLABEL-37	RESPIRATOR/GLASSES LABEL VL
114	PLABEL-12	READ MANUAL LABEL VL
115	PLABEL-15	EAR PROTECTION LABEL VL
116	PLABEL-14	ELECTRICITY LABEL

REF	PART #	DESCRIPTION

117	P0453117	MACHINE ID LABEL
334	P0453334	GRIZZLY.COM LABEL
446	G8588	GRIZZLY NAMEPLATE
447	P0453447	MODEL NUMBER LABEL
451	PPAINT-1	GRIZZLY GREEN TOUCH UP PAINT
452	PPAINT-11	GRIZZLY PUTTY TOUCH UP PAINT

Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels.

-56-	G0453/G0454 (Mfg. Since 3/08)

Image 58

Contents Model G0453/G0454 15 & 20 Mobile Planers Page Table of Contents Manual Accuracy Contact Info IntroductionMachine Description Identification ON/OFFInternal Components Machine Data Sheet Other G0454 Machine Data Sheet Knife Adjustment Jack Screws and Springs Safety Safety Instructions for MachineryUnattended OPERATION. Never leave Additional Safety Instructions for Planers Full-Load Current Rating Power SupplyAvailability G0453 220V Circuit RequirementsG0453 Grounding InstructionsExtension Cords G0454Unpacking SetupNeeded for Setup Description QtyBox Inventory Figure Qty InventoryG0454 Hardware and Tools not shown Before cleaning, gather the following CleanupBasic steps for removing rust preventative Site Considerations Lifting & Moving Base Unit AssemblyTo assemble your planer Attaching magnetic switch Foot pedal and caster installed G0453/G0454 Mfg. Since 3/08 Dust Collection Test Run Check Gearbox OilFactory adjustments that should be verified Recommended AdjustmentsRe-Tension V-Belts Operations Operation OverviewPlaning Tips Workpiece InspectionWood Hardness Feed Rate Species HardnessDepth of Cut Bed Roller HeightTo adjust the bed rollers Disconnect Planer from PowerAccessories G2790 Universal Knife GrinderT20502 T20452 T20503 T20448 T20456 H0736 G8982-Roller TableCleaning Protecting MaintenanceSchedule Columns and Leadscrews LubricationFeed Roller Bushings Table Height Worm GearDrive Chain & Sprockets Table Height Chain & SprocketsGearbox Oil Troubleshooting ServiceMotor & Electrical Machine Operation Amount of snipeAdjust the height of the chip breaker or pressure bar To adjust the height of the knives Setting/Replacing KnivesTools Needed Qty Belt Tensioning Replacement To tension/replace the V-beltsPage To adjust the table height chain tension Table Height Chain TensionFeed Rollers, Chip Breaker & Pressure Bar Heights Using a RotacatorDist. Below Knife Edge at BDC Figure Adjustment Jam Nut Set Screw Using Wood Blocks Roller Spring Tension To adjust the chip deflector gapPositioning Chip Deflector Anti-Kickback Fingers Scale CalibrationTo re-position the scale Pulley Alignment To check/re-align pulleysWiring Wiring Safety InstructionsG0453 Wiring Diagram Magnetic ON/OFF SwitchG0454 Wiring Diagram NHD BTH-21Parts G0453 Headstock Parts List DescriptionG0453 Table Breakdown G0453 Columns Breakdown G0453 Cabinet Stand Breakdown G0453 Cabinet Stand Parts List G0453 Gearbox Breakdown G0453 Label Placement G0454 Headstock Breakdown G0454 Headstock Parts List PN01M HEX NUT M6-1 PSS25M SET Screw M6-1 X PB09M G0454 Table Breakdown G0454 Columns Breakdown 310G0454 Cabinet Stand Breakdown G0454 Cabinet Stand Parts List G0454 Gearbox Breakdown 538G0454 Label Placement G0453/G0454 Mfg. Since 3/08 Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty and Returns Warranty and ReturnsOrder Hours a DAY