Grizzly G0454 owner manual G0453 Columns Breakdown

Page 54

G0453 Columns Breakdown

320

322

305

314

323	328
	328
	327
	315
	313
	312	333
		333

316

329

326

332

330

304

330

331

	311	310
		307
	309	306
	309	303
		303
	308

318

324

325

319 320

317

321

314

305

REF	PART #	DESCRIPTION

303	P0453303	CHAIN 12.7 AX 134
304	PR05M	EXT RETAINING RING 15MM
305	P0453305	LIFTING BAR
306	PB09M	HEX BOLT M8-1.25 X 20
307	PW01M	FLAT WASHER 8MM
308	PR05M	EXT RETAINING RING 15MM
309	P0453309	SPROCKET
310	P0453310	BRACKET
311	P0453311	SHAFT
312	PN02M	HEX NUT M10-1.5
313	PW04M	FLAT WASHER 10MM
314	PK08M	KEY 5 X 5 X 16
315	P0453315	SPROCKET
316	PR03M	EXT RETAINING RING 12MM
317	PK69M	KEY 4 X 4 X 12
318	P0453318	GEAR

REF	PART #	DESCRIPTION

319	PSB02M	CAP SCREW M6-1 X 20
320	P0453320	LEADSCREW NUT
321	P0453321	PRIMARY LEADSCREW
322	P0453322	SECONDARY LEADSCREW
323	PSS13M	SET SCREW M10-1.5 X 12
324	PR23M	INT RETAINING RING 40MM
325	P0453325	BUSHING
326	P0453326	PRIMARY COLUMN
327	PR24M	INT RETAINING RING 42MM
328	P6302	BALL BEARING 6302
329	P0453329	SECONDARY COLUMN
330	PW06M	FLAT WASHER 12MM
331	PN09M	HEX NUT M12-1.75
332	PB24M	HEX BOLT M12-1.75 X 45
333	P0453333	BASE

-52-	G0453/G0454 (Mfg. Since 3/08)

Image 54

Contents Model G0453/G0454 15 & 20 Mobile Planers Page Table of Contents Introduction Manual Accuracy Contact InfoMachine Description Identification ON/OFFInternal Components Machine Data Sheet Other G0454 Machine Data Sheet Knife Adjustment Jack Screws and Springs Safety Safety Instructions for MachineryUnattended OPERATION. Never leave Additional Safety Instructions for Planers Full-Load Current Rating Power SupplyAvailability G0453 220V Circuit RequirementsG0453 Grounding InstructionsExtension Cords G0454Unpacking SetupNeeded for Setup Description QtyInventory Box Inventory Figure QtyG0454 Hardware and Tools not shown Cleanup Before cleaning, gather the followingBasic steps for removing rust preventative Site Considerations Assembly Lifting & Moving Base UnitTo assemble your planer Attaching magnetic switch Foot pedal and caster installed G0453/G0454 Mfg. Since 3/08 Dust Collection Test Run Check Gearbox OilRecommended Adjustments Factory adjustments that should be verifiedRe-Tension V-Belts Operations Operation OverviewPlaning Tips Workpiece InspectionWood Hardness Feed Rate Species HardnessDepth of Cut Bed Roller HeightTo adjust the bed rollers Disconnect Planer from PowerAccessories G2790 Universal Knife GrinderT20502 T20452 T20503 T20448 T20456 H0736 G8982-Roller TableMaintenance Cleaning ProtectingSchedule Columns and Leadscrews LubricationFeed Roller Bushings Table Height Worm GearTable Height Chain & Sprockets Drive Chain & SprocketsGearbox Oil Service TroubleshootingMotor & Electrical Machine Operation Amount of snipeAdjust the height of the chip breaker or pressure bar Setting/Replacing Knives To adjust the height of the knivesTools Needed Qty Belt Tensioning Replacement To tension/replace the V-beltsPage To adjust the table height chain tension Table Height Chain TensionUsing a Rotacator Feed Rollers, Chip Breaker & Pressure Bar HeightsDist. Below Knife Edge at BDC Figure Adjustment Jam Nut Set Screw Using Wood Blocks To adjust the chip deflector gap Roller Spring TensionPositioning Chip Deflector Scale Calibration Anti-Kickback FingersTo re-position the scale Pulley Alignment To check/re-align pulleysWiring Wiring Safety InstructionsG0453 Wiring Diagram Magnetic ON/OFF SwitchG0454 Wiring Diagram NHD BTH-21Parts G0453 Headstock Parts List DescriptionG0453 Table Breakdown G0453 Columns Breakdown G0453 Cabinet Stand Breakdown G0453 Cabinet Stand Parts List G0453 Gearbox Breakdown G0453 Label Placement G0454 Headstock Breakdown G0454 Headstock Parts List PN01M HEX NUT M6-1 PSS25M SET Screw M6-1 X PB09M G0454 Table Breakdown G0454 Columns Breakdown 310G0454 Cabinet Stand Breakdown G0454 Cabinet Stand Parts List G0454 Gearbox Breakdown 538G0454 Label Placement G0453/G0454 Mfg. Since 3/08 Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty and Returns Warranty and ReturnsOrder Hours a DAY