Grizzly G0453, G0454 owner manual Site Considerations

Page 19

Site Considerations

Weight Load

Refer to the Machine Data Sheet for the weight of your machine. Make sure that the surface upon which the machine is placed will bear the weight of the machine, additional equipment that may be installed on the machine, and the heaviest work- piece that will be used. Additionally, consider the weight of the operator and any dynamic loading that may occur when operating the machine.

Space Allocation

Consider the largest size of workpiece that will be processed through this machine and provide enough space around the machine for adequate operator material handling or the installation of auxiliary equipment. With permanent installations, leave enough space around the machine to open or remove doors/covers as required by the main- tenance and service described in this manual.

See below for required space allocation.

Children or untrained people may be seriously injured by this machine. Only install in an access restricted location.

Physical Environment

The physical environment where your machine is operated is important for safe operation and the longevity of its components. For best results, operate this machine in a dry environment that is free from excessive moisture, hazardous chemi- cals, airborne abrasives, or extreme conditions. Extreme conditions for this type of machinery are generally those where the ambient temperature range exceeds 41°–104°F; the relative humidity range exceeds 20–95% (non-condensing); or the environment is subject to vibration, shocks, or bumps.

Electrical Installation

Place this machine near an existing power source. Make sure all power cords are protected from traffic, material handling, moisture, chemicals, or other hazards. Make sure to leave access to a means of disconnecting the power source or engaging a lockout/tagout device.

Lighting

Lighting around the machine must be adequate enough that operations can be performed safely. Shadows, glare, or strobe effects that may distract or impede the operator must be eliminated.

Model G0453

X = 42"

Y = 28"

Model G0454

X = 555⁄8"

Y = 365⁄8"

Y

Dust

Port

X

Feed Direction

Figure 6. Minimum working clearances.

G0453/G0454 (Mfg. Since 3/08)

-17-

Image 19

Contents Model G0453/G0454 15 & 20 Mobile Planers Page Table of Contents Manual Accuracy Contact Info IntroductionMachine Description ON/OFF IdentificationInternal Components Machine Data Sheet Other G0454 Machine Data Sheet Knife Adjustment Jack Screws and Springs Safety Instructions for Machinery SafetyUnattended OPERATION. Never leave Additional Safety Instructions for Planers G0453 220V Circuit Requirements Power SupplyAvailability Full-Load Current RatingG0454 Grounding InstructionsExtension Cords G0453Description Qty SetupNeeded for Setup UnpackingBox Inventory Figure Qty InventoryG0454 Hardware and Tools not shown Before cleaning, gather the following CleanupBasic steps for removing rust preventative Site Considerations Lifting & Moving Base Unit AssemblyTo assemble your planer Attaching magnetic switch Foot pedal and caster installed G0453/G0454 Mfg. Since 3/08 Check Gearbox Oil Dust Collection Test RunFactory adjustments that should be verified Recommended AdjustmentsRe-Tension V-Belts Operation Overview OperationsWorkpiece Inspection Planing TipsSpecies Hardness Wood Hardness Feed RateBed Roller Height Depth of CutDisconnect Planer from Power To adjust the bed rollersG2790 Universal Knife Grinder AccessoriesG8982-Roller Table T20502 T20452 T20503 T20448 T20456 H0736Cleaning Protecting MaintenanceSchedule Table Height Worm Gear LubricationFeed Roller Bushings Columns and LeadscrewsDrive Chain & Sprockets Table Height Chain & SprocketsGearbox Oil Troubleshooting ServiceMotor & Electrical Amount of snipe Machine OperationAdjust the height of the chip breaker or pressure bar To adjust the height of the knives Setting/Replacing KnivesTools Needed Qty To tension/replace the V-belts Belt Tensioning ReplacementPage Table Height Chain Tension To adjust the table height chain tensionFeed Rollers, Chip Breaker & Pressure Bar Heights Using a RotacatorDist. Below Knife Edge at BDC Figure Adjustment Jam Nut Set Screw Using Wood Blocks Roller Spring Tension To adjust the chip deflector gapPositioning Chip Deflector Anti-Kickback Fingers Scale CalibrationTo re-position the scale To check/re-align pulleys Pulley AlignmentWiring Safety Instructions WiringMagnetic ON/OFF Switch G0453 Wiring DiagramNHD BTH-21 G0454 Wiring DiagramParts Description G0453 Headstock Parts ListG0453 Table Breakdown G0453 Columns Breakdown G0453 Cabinet Stand Breakdown G0453 Cabinet Stand Parts List G0453 Gearbox Breakdown G0453 Label Placement G0454 Headstock Breakdown G0454 Headstock Parts List PN01M HEX NUT M6-1 PSS25M SET Screw M6-1 X PB09M G0454 Table Breakdown 310 G0454 Columns BreakdownG0454 Cabinet Stand Breakdown G0454 Cabinet Stand Parts List 538 G0454 Gearbox BreakdownG0454 Label Placement G0453/G0454 Mfg. Since 3/08 Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty and Returns Warranty and ReturnsOrder Hours a DAY