Grizzly G0453, G0454 owner manual Safety Instructions for Machinery

Page 11

SECTION 1: SAFETY

For Your Own Safety, Read Instruction Manual Before Operating this Machine

The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of impor- tance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.

 

 

Indicates an imminently hazardous situation which, if not avoided,

 

 

 

 

WILL result in death or serious injury.

 

 

Indicates a potentially hazardous situation which, if not avoided,

 

 

 

 

COULd result in death or serious injury.

 

 

 

 

Indicates a potentially hazardous situation which, if not avoided,

 

 

 

 

MAY result in minor or moderate injury. It may also be used to alert

 

 

 

 

against unsafe practices.

NOTICE

This symbol is used to alert the user to useful information about

proper operation of the machine.

Safety Instructions for Machinery

OWNER’S MANUAL. Read and understand this owner’s manual BEFORE using machine. Untrained users can be seriously hurt.

EYE PROTECTION. Always wear ANSI-approved safety glasses or a face shield when operating or observing machinery to reduce the risk of eye injury or blindness from flying particles. Everyday eyeglasses are not approved safety glasses.

HAzARdOUS dUST. Dust created while using machinery may cause cancer, birth defects, or long-term respiratory damage. Be aware of dust hazards associated with each workpiece material, and always wear a NIOSH-approved respirator to reduce your risk.

WEARING PROPER APPAREL. Do not wear clothing, apparel, or jewelry that can become entangled in moving parts. Always tie back or cover long hair. Wear non-slip footwear to avoid accidental slips which could cause a loss of work- piece control.

HEARING PROTECTION. Always wear hear- ing protection when operating or observiing loud machinery. Extended exposure to this noise without hearing protection can cause permanent hearing loss.

MENTAL ALERTNESS. Be mentally alert when running machinery. Never operate under the influence of drugs or alcohol, when tired, or when distracted.

G0453/G0454 (Mfg. Since 3/08)

-9-

Image 11
Contents Model G0453/G0454 15 & 20 Mobile Planers Page Table of Contents Machine Description IntroductionManual Accuracy Contact Info ON/OFF IdentificationInternal Components Machine Data Sheet Other G0454 Machine Data Sheet Knife Adjustment Jack Screws and Springs Safety Instructions for Machinery SafetyUnattended OPERATION. Never­ leave­ Additional Safety Instructions for Planers G0453 220V Circuit Requirements Power SupplyAvailability Full-Load Current RatingG0454 Grounding InstructionsExtension Cords G0453Description Qty SetupNeeded for Setup UnpackingG0454 Hardware and Tools not shown InventoryBox Inventory Figure Qty Basic steps for removing rust preventative CleanupBefore cleaning, gather the following Site Considerations To assemble your planer AssemblyLifting & Moving Base Unit Attaching magnetic switch Foot pedal and caster installed G0453/G0454 Mfg. Since 3/08 Check Gearbox Oil Dust Collection Test RunRe-Tension V-Belts Recommended AdjustmentsFactory adjustments that should be verified Operation Overview OperationsWorkpiece Inspection Planing TipsSpecies Hardness Wood Hardness Feed RateBed Roller Height Depth of CutDisconnect Planer from Power To adjust the bed rollersG2790 Universal Knife Grinder AccessoriesG8982-Roller Table T20502 T20452 T20503 T20448 T20456 H0736Schedule MaintenanceCleaning Protecting Table Height Worm Gear LubricationFeed Roller Bushings Columns and LeadscrewsGearbox Oil Table Height Chain & SprocketsDrive Chain & Sprockets Motor & Electrical ServiceTroubleshooting Amount of snipe Machine OperationAdjust the height of the chip breaker or pressure bar Tools Needed Qty Setting/Replacing KnivesTo adjust the height of the knives To tension/replace the V-belts Belt Tensioning ReplacementPage Table Height Chain Tension To adjust the table height chain tensionDist. Below Knife Edge at BDC Figure Using a RotacatorFeed Rollers, Chip Breaker & Pressure Bar Heights Adjustment Jam Nut Set Screw Using Wood Blocks Positioning Chip Deflector To adjust the chip deflector gapRoller Spring Tension To re-position the scale Scale CalibrationAnti-Kickback Fingers To check/re-align pulleys Pulley AlignmentWiring Safety Instructions WiringMagnetic ON/OFF Switch G0453 Wiring DiagramNHD BTH-21 G0454 Wiring DiagramParts Description G0453 Headstock Parts ListG0453 Table Breakdown G0453 Columns Breakdown G0453 Cabinet Stand Breakdown G0453 Cabinet Stand Parts List G0453 Gearbox Breakdown G0453 Label Placement G0454 Headstock Breakdown G0454 Headstock Parts List PN01M HEX NUT M6-1 PSS25M SET Screw M6-1 X PB09M G0454 Table Breakdown 310 G0454 Columns BreakdownG0454 Cabinet Stand Breakdown G0454 Cabinet Stand Parts List 538 G0454 Gearbox BreakdownG0454 Label Placement G0453/G0454 Mfg. Since 3/08 Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty and Returns Warranty and ReturnsOrder Hours a DAY