Grizzly Wiring Diagram and Safety Instructions for Your Go454 Planer

Page 50

wiring diagram g0545

G0454 Wiring Diagram

Magnetic ON/OFF Switch

A1			A2
1L1	3L2	5L3	NO13
	Contactor		17	Grnd
	NHD 35D		17	Grnd
	NHD 35D		ON
	220V		ON
	220V		18
			18

NO14

2T1	4T2	6T3
		A2

			OFF
26		OL Relay
	30	OL Relay
28	32
		NHD BTH-21
98	97	96	95

2T1 4T2 6T3

The motor wiring shown here is current at the time of printing, but it may not match your machine. Always use the wiring diagram inside the motor junction box.

	NEMA L6-30 Plug
	(As Recommended)
	Hot
	G
	Ground
	Hot
	Motor
Grnd	Start Capacitor
	Start Capacitor
	300MFD 250VAC

Run Capacitor

60MFD 400VAC

-48-	READ ELECTRICAL SAFETY	G0453/G0454 (Mfg. Since 3/08)
	ON PAGE 46!

Image 50

Contents Model G0453/G0454 15 & 20 Mobile Planers Page Table of Contents Machine Description IntroductionManual Accuracy Contact Info Identification ON/OFFInternal Components Machine Data Sheet Other G0454 Machine Data Sheet Knife Adjustment Jack Screws and Springs Safety Safety Instructions for MachineryUnattended OPERATION. Never leave Additional Safety Instructions for Planers Full-Load Current Rating Power SupplyAvailability G0453 220V Circuit RequirementsG0453 Grounding InstructionsExtension Cords G0454Unpacking SetupNeeded for Setup Description QtyG0454 Hardware and Tools not shown InventoryBox Inventory Figure Qty Basic steps for removing rust preventative CleanupBefore cleaning, gather the following Site Considerations To assemble your planer AssemblyLifting & Moving Base Unit Attaching magnetic switch Foot pedal and caster installed G0453/G0454 Mfg. Since 3/08 Dust Collection Test Run Check Gearbox OilRe-Tension V-Belts Recommended AdjustmentsFactory adjustments that should be verified Operations Operation OverviewPlaning Tips Workpiece InspectionWood Hardness Feed Rate Species HardnessDepth of Cut Bed Roller HeightTo adjust the bed rollers Disconnect Planer from PowerAccessories G2790 Universal Knife GrinderT20502 T20452 T20503 T20448 T20456 H0736 G8982-Roller TableSchedule MaintenanceCleaning Protecting Columns and Leadscrews LubricationFeed Roller Bushings Table Height Worm GearGearbox Oil Table Height Chain & SprocketsDrive Chain & Sprockets Motor & Electrical ServiceTroubleshooting Machine Operation Amount of snipeAdjust the height of the chip breaker or pressure bar Tools Needed Qty Setting/Replacing KnivesTo adjust the height of the knives Belt Tensioning Replacement To tension/replace the V-beltsPage To adjust the table height chain tension Table Height Chain TensionDist. Below Knife Edge at BDC Figure Using a RotacatorFeed Rollers, Chip Breaker & Pressure Bar Heights Adjustment Jam Nut Set Screw Using Wood Blocks Positioning Chip Deflector To adjust the chip deflector gapRoller Spring Tension To re-position the scale Scale CalibrationAnti-Kickback Fingers Pulley Alignment To check/re-align pulleysWiring Wiring Safety InstructionsG0453 Wiring Diagram Magnetic ON/OFF SwitchG0454 Wiring Diagram NHD BTH-21Parts G0453 Headstock Parts List DescriptionG0453 Table Breakdown G0453 Columns Breakdown G0453 Cabinet Stand Breakdown G0453 Cabinet Stand Parts List G0453 Gearbox Breakdown G0453 Label Placement G0454 Headstock Breakdown G0454 Headstock Parts List PN01M HEX NUT M6-1 PSS25M SET Screw M6-1 X PB09M G0454 Table Breakdown G0454 Columns Breakdown 310G0454 Cabinet Stand Breakdown G0454 Cabinet Stand Parts List G0454 Gearbox Breakdown 538G0454 Label Placement G0453/G0454 Mfg. Since 3/08 Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty and Returns Warranty and ReturnsOrder Hours a DAY