Grizzly G0453 owner manual G0454 Cabinet Stand Breakdown

Page 64

G0454 Cabinet Stand Breakdown

429-1 429-4

429-2 429-5

440A

441

429-6

429
447
427		433
427
428
437		434
		434
	438	436
		436
		428
		426
		440

430 431

432

	404
	408
407	406	405	401
			401

	406

409

412

406

405

542

439

410		442
411
416		422423
415		422423
415	413	425
443		421 420
	417	421 420	419
	417		419
	444	415	418
		415
		414
		414	424
			424

-62-	G0453/G0454 (Mfg. Since 3/08)

Image 64

Contents Model G0453/G0454 15 & 20 Mobile Planers Page Table of Contents Manual Accuracy Contact Info IntroductionMachine Description Identification ON/OFFInternal Components Machine Data Sheet Other G0454 Machine Data Sheet Knife Adjustment Jack Screws and Springs Safety Safety Instructions for MachineryUnattended OPERATION. Never leave Additional Safety Instructions for Planers Power Supply AvailabilityFull-Load Current Rating G0453 220V Circuit RequirementsGrounding Instructions Extension CordsG0453 G0454Setup Needed for SetupUnpacking Description QtyBox Inventory Figure Qty InventoryG0454 Hardware and Tools not shown Before cleaning, gather the following CleanupBasic steps for removing rust preventative Site Considerations Lifting & Moving Base Unit AssemblyTo assemble your planer Attaching magnetic switch Foot pedal and caster installed G0453/G0454 Mfg. Since 3/08 Dust Collection Test Run Check Gearbox OilFactory adjustments that should be verified Recommended AdjustmentsRe-Tension V-Belts Operations Operation OverviewPlaning Tips Workpiece InspectionWood Hardness Feed Rate Species HardnessDepth of Cut Bed Roller HeightTo adjust the bed rollers Disconnect Planer from PowerAccessories G2790 Universal Knife GrinderT20502 T20452 T20503 T20448 T20456 H0736 G8982-Roller TableCleaning Protecting MaintenanceSchedule Lubrication Feed Roller BushingsColumns and Leadscrews Table Height Worm GearDrive Chain & Sprockets Table Height Chain & SprocketsGearbox Oil Troubleshooting ServiceMotor & Electrical Machine Operation Amount of snipeAdjust the height of the chip breaker or pressure bar To adjust the height of the knives Setting/Replacing KnivesTools Needed Qty Belt Tensioning Replacement To tension/replace the V-beltsPage To adjust the table height chain tension Table Height Chain TensionFeed Rollers, Chip Breaker & Pressure Bar Heights Using a RotacatorDist. Below Knife Edge at BDC Figure Adjustment Jam Nut Set Screw Using Wood Blocks Roller Spring Tension To adjust the chip deflector gapPositioning Chip Deflector Anti-Kickback Fingers Scale CalibrationTo re-position the scale Pulley Alignment To check/re-align pulleysWiring Wiring Safety InstructionsG0453 Wiring Diagram Magnetic ON/OFF SwitchG0454 Wiring Diagram NHD BTH-21Parts G0453 Headstock Parts List DescriptionG0453 Table Breakdown G0453 Columns Breakdown G0453 Cabinet Stand Breakdown G0453 Cabinet Stand Parts List G0453 Gearbox Breakdown G0453 Label Placement G0454 Headstock Breakdown G0454 Headstock Parts List PN01M HEX NUT M6-1 PSS25M SET Screw M6-1 X PB09M G0454 Table Breakdown G0454 Columns Breakdown 310G0454 Cabinet Stand Breakdown G0454 Cabinet Stand Parts List G0454 Gearbox Breakdown 538G0454 Label Placement G0453/G0454 Mfg. Since 3/08 Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty and Returns Warranty and ReturnsOrder Hours a DAY