Grizzly G0454, G0453 owner manual Accessories, G2790 Universal Knife Grinder

Page 30

ACCESSORIES

SECTION 5: ACCESSORIES

Some aftermarket accessories can be installed on this machine that could cause it to function improperly, increasing the risk of serious personal injury. To minimize this risk, only install accessories recommended for this machine by Grizzly.

NOTICE

Refer to the newest copy of the Grizzly Catalog for other accessories available for this machine.

G1738—Rotacator™ Precision Planer Tool

The Rotacator is a dial indicator on a magnetic base and is designed for quickly and accurate- ly setting the critical tolerances needed when adjusting any planer, so that nasty surprises such as non-parallel and chattered cuts can be elimi- nated. Helps adjust infeed/outfeed rollers, pres- sure bars, chip breakers, and bed rollers. Also a great setup tool for other machines! Accurate to 0.001". Indicator rotates 360°

G6701—HSS Replacement Knives for Model G0453, Set of 3

G6702—HSS Replacement Knives for Model G0454, Set of 4

G2790—Universal Knife Grinder

This dry-type Knife Grinder is ideal for sharpen- ing planer and jointer knives. High quality cast iron construction, together with large knife hold- ing capacity (will sharpen up to 20" planer/jointer knives) makes this grinder an excellent invest- ment. Features a heavy-duty 1⁄2 HP 110V motor, knife holding angle adjustable from 20° to 70°, and adjustable-height 120 grit grinding wheel.

Figure 21. G2790 Universal Knife Grinder.

H7768—15" Byrd® Shelix Cutterhead H7768—20" Byrd® Shelix Cutterhead

Made in the USA by Byrd, this indexable carbide insert cutterhead is the best money can buy— period! The inserts are not only placed in a spiral pattern, they are also positioned at an angle so the shearing action leaves a glassy smooth cut on the toughest and most figured woods. Comes with 5 extra replacement inserts. Great upgrade!

Figure 20. Rotacator™ Precision Planer Tool.

Figure 22. Byrd® Shelix Cutterhead.

-28-	G0453/G0454 (Mfg. Since 3/08)

Image 30

Contents Model G0453/G0454 15 & 20 Mobile Planers Page Table of Contents Introduction Manual Accuracy Contact InfoMachine Description Identification ON/OFFInternal Components Machine Data Sheet Other G0454 Machine Data Sheet Knife Adjustment Jack Screws and Springs Safety Safety Instructions for MachineryUnattended OPERATION. Never leave Additional Safety Instructions for Planers Full-Load Current Rating Power SupplyAvailability G0453 220V Circuit RequirementsG0453 Grounding InstructionsExtension Cords G0454Unpacking SetupNeeded for Setup Description QtyInventory Box Inventory Figure QtyG0454 Hardware and Tools not shown Cleanup Before cleaning, gather the followingBasic steps for removing rust preventative Site Considerations Assembly Lifting & Moving Base UnitTo assemble your planer Attaching magnetic switch Foot pedal and caster installed G0453/G0454 Mfg. Since 3/08 Dust Collection Test Run Check Gearbox OilRecommended Adjustments Factory adjustments that should be verifiedRe-Tension V-Belts Operations Operation OverviewPlaning Tips Workpiece InspectionWood Hardness Feed Rate Species HardnessDepth of Cut Bed Roller HeightTo adjust the bed rollers Disconnect Planer from PowerAccessories G2790 Universal Knife GrinderT20502 T20452 T20503 T20448 T20456 H0736 G8982-Roller TableMaintenance Cleaning ProtectingSchedule Columns and Leadscrews LubricationFeed Roller Bushings Table Height Worm GearTable Height Chain & Sprockets Drive Chain & SprocketsGearbox Oil Service TroubleshootingMotor & Electrical Machine Operation Amount of snipeAdjust the height of the chip breaker or pressure bar Setting/Replacing Knives To adjust the height of the knivesTools Needed Qty Belt Tensioning Replacement To tension/replace the V-beltsPage To adjust the table height chain tension Table Height Chain TensionUsing a Rotacator Feed Rollers, Chip Breaker & Pressure Bar HeightsDist. Below Knife Edge at BDC Figure Adjustment Jam Nut Set Screw Using Wood Blocks To adjust the chip deflector gap Roller Spring TensionPositioning Chip Deflector Scale Calibration Anti-Kickback FingersTo re-position the scale Pulley Alignment To check/re-align pulleysWiring Wiring Safety InstructionsG0453 Wiring Diagram Magnetic ON/OFF SwitchG0454 Wiring Diagram NHD BTH-21Parts G0453 Headstock Parts List DescriptionG0453 Table Breakdown G0453 Columns Breakdown G0453 Cabinet Stand Breakdown G0453 Cabinet Stand Parts List G0453 Gearbox Breakdown G0453 Label Placement G0454 Headstock Breakdown G0454 Headstock Parts List PN01M HEX NUT M6-1 PSS25M SET Screw M6-1 X PB09M G0454 Table Breakdown G0454 Columns Breakdown 310G0454 Cabinet Stand Breakdown G0454 Cabinet Stand Parts List G0454 Gearbox Breakdown 538G0454 Label Placement G0453/G0454 Mfg. Since 3/08 Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty and Returns Warranty and ReturnsOrder Hours a DAY