Remington 495 operating instructions Troubleshooting Guide, Problem Possible Cause Remedy

Page 37

Troubleshooting Guide

PROBLEM

POSSIBLE CAUSE

REMEDY

 

Piston hangs out

Tool overdriven.

Tap piston on hard surface

of muzzle.

 

until piston is pushed back

 

 

into the guide. (See Over-

 

 

driven Fastener below)

 

 

 

 

 

Piston not properly

Remove barrel assembly

 

 

assembled in relation to

(see pages 28-32). Replace

 

stop.

all damaged or missing parts.

 

 

 

 

 

Broken piston or piston ring.

Replace piston or piston ring

 

 

or take tool to your distributor.

 

 

 

Overdriven

Excessive power.

Change either to next lower

fastener.

 

power load or next longer

 

 

length fastener.

 

 

 

 

Piston jammed.

Overdriving of fastener (see

Remove barrel assembly

 

above).

(see pages 28-32). Replace

 

 

other parts if damaged.

 

 

 

 

Power load strip will

Advance bar or spring

Replace advance bar or

not advance.

damaged

springs.

 

 

 

 

 

Tool dirty.

Clean tool. Notice: Do not

 

 

attempt to clean power load

 

 

strip channel with wire brush.

 

 

You may damage tool.

 

 

 

 

Reduction or loss

Piston not returning to full

Barrel must be opened to the

of power.

rear position.

full extended position to

 

 

properly position piston.

 

 

 

 

 

Worn piston ring or broken

Replace piston and/or piston

 

piston.

ring or take tool to your dis-

 

 

tributor.

 

 

 

 

Tool does not

Misassembled or damaged

Remove firing pin guide and

completely depress.

sear, firing pin parts, or

check all parts for correct fit

 

guide.

assembly.

 

 

 

 

Tool does not fire.

Failure of tool to depress

See data listed under Tool

 

completely.

does not completely de-

 

 

press, above.

 

 

 

 

 

Piston not fully reset.

Fully reset piston. See step 1

 

 

under Operation, page 21.

 

 

 

 

 

Dirt buildup on sear not

Check firing pin mark on

 

allowing proper penetration

power load. Clean firing pin

 

of firing pin or worn firing

guide, sear and firing pin. Re-

 

pin.

place worn or damaged

 

 

parts. Notice: Do not attempt

 

 

to clean power load strip

 

 

channel with wire brush. You

 

 

may damage tool.

 

 

 

 

Opening and clos-

Lack of proper cleaning.

Inspect and clean complete

ing of barrel or

 

tool. Replace worn or dam-

pushing down on

 

aged parts. Notice: Do not

tool, etc. is not

 

attempt to clean power load

smooth but is

 

strip channel with wire brush.

rough or binds.

 

You may damage tool.

 

 

 

 

101719

 

 

 

37

Image 37
Contents Operating Instructions Mode d’emploi Index Remington Avertissement Mesures de précautions Safety Precautions Mesures de pré cautions Handling the Tool Manipulation DE L’OUTIL Powd Safety Precautions Mesures de pré cautions ? ? Tile Brick Glasscarrelage Brique Weld Soudure Utilisation DE L’OUTIL Power Loads and Fasteners Charges ET Fixations Endommager l’outil voir Power Load Strips Only Charges DE Poudre Seulement Head Shank Tê te Tige Plastic Flute Cannelure de plastique Why a Power Fastener Holds Pourquoi les fixations tiennent WHY a Power Fastener Holds in Steel Fastening Into Concrete Overdriven Power Fasteners and Piston Operation Utilisation Operation Operation Key Part Description Parts List 495101719 Code Piè ce Description Liste de piè ces 495Cleaning and Maintenance Nettoyage et entretien Removing Barrel Assembly DÉ Pose DE L’ENSEMBLE DE Canon Tool Disassembly Dé sassemblage du pistoletSeparating Barrel Assembly from Housing Removing Handle Pad Assembly and Rear Pad Removing Firing PIN DÉ Pose DU Percuteur Removing Trigger Assembly DÉ Pose DE L’ENSEMBLE DE DÉ TenteTool Assembly Assemblage du pistolet Suite Replacing Handle Pad Assembly and Rear Pad Inserting Piston in Barrel Assembling Barrel Assembly Montage DE L’ENSEMBLE DE CanonPushing Stop towards Front of Tool Problem Possible Cause Remedy Troubleshooting GuideDé pannage Problè ME Cause Possible SolutionSP Fasteners Fixations SP Fasteners FixationsApplication Chart Tableau d’application 482-90 Application Chart Tableau d’applicationDesa Industries Canada, Inc Limited Warranty AgreementAccord de garantie limité e