Miller Electric Auto Axcess 675 manual Peripheral Receptacle Functions, Socket Information

Page 21

3-10. Peripheral Receptacle Functions

D C B

A

E L

M

FK

H J

Function

Socket

Socket Information

 

A

Not used.

 

B

Not used.

 

C*

Circuit common.

Purge

D

Contact closure to C completes 40 volts dc

 

 

 

solenoid circuit to purge shielding gas line.

 

E

Contact closure to F indicates coolant flow switch is

Coolant Flow

 

closed and recirculating coolant system is

 

operational.

Switch Input

 

 

 

Signal

 

 

 

F*

Circuit common.

Jog

H**

Contact closure to circuit common advances

 

 

welding wire at wire drive assembly.

Retract

J**

Contact closure to circuit common retracts welding

 

 

wire at wire drive assembly.

 

K

Contact closure to L energizes Touch Sensor

 

 

circuitry.

Touch Sensor ON

L*

Circuit common.

And Output Signal

 

 

 

M

Part touched +24 volts dc output signal referenced

Ref. 802 915-A

 

to circuit common.

 

 

*Circuit common is same electrical reference point.

**Speed of Jog + (advance) and Jog − (retract) is 60 ipm for 3 seconds, then it automatically changes to 700 ipm.

Note: A customer supplied matching amphenol plug, factory Part No. 194 847, [Amphenol Part No. 97-3106A-20-33P(B)(621) and strain relief clamp 97-3057-12(0621)] is required to use peripheral receptacle.

OM-201 540 Page 17

Image 21
Contents Processes OM-201 540KDescription File Advanced Manufacturing SystemsFrom Miller to You Table of Contents Warranty Arc Welding Hazards Symbol UsageElectric Shock can kill HOT Parts can cause severe burnsARC Rays can burn eyes and skin Fumes and Gases can be hazardousWelding can cause fire or explosion Flying Metal or Dirt can injure eyesFire or Explosion hazard Welding Wire can cause injuryFalling Unit can cause injury Moving Parts can cause injuryCalifornia Proposition 65 Warnings Principal Safety StandardsEMF Information About Implanted Medical DevicesUNE Décharge Électrique peut entraîner la mort Symboles utilisésDES Pièces Chaudes peuvent provoquer des brûlures graves LES Fumées ET LES GAZ peuvent être dangereuxLE Soudage peut provoquer un in cendie ou une explosion LES Bouteilles peuvent exploser si elles sont endommagées LE Bruit peut endommager l’ouïeRisque D’INCENDIE OU D’EXPLO LA Chute DE L’APPAREIL peut blesserProposition californienne 65 Avertissements LES Fils DE Soudage peuvent provoquer des blessuresLE Soudage À L’ARC risque de provoquer des interférences Principales normes de sécurité Information EMFEn ce qui concerne les implants médicaux OM-201 540 − Installation SpecificationsDimensions And Weight Volt-Ampere Curves Duty Cycle And Overheating100% Duty Cycle At 675 Amperes OverheatingSelecting a Location Connection DiagramMovement Do not move or operate Tipping Do not stack units. Beware of tippingRear Panel Receptacles And Supplementary Protectors Incorrect Installation Connecting To Weld TerminalsSelecting Weld Cable Sizes Socket Information Peripheral Receptacle FunctionsMotor Control Receptacle Functions Hz Three Phase Input Voltage Electrical Service GuideInput Amperes At Rated Output Normal OperatingConnecting Input Power Welding Power Source Input Power ConnectionsDisconnect Device Input Power Connections Touch Sensor Operation Remote Program SettingRemote Program Select Program No Output a Output B Output COperational Terms − OperationWeld StartCrater PostflowFront Panel Controls See Section Wire Type LEDProcess LED Gas Type LEDSTL Robot Abbreviations Front Panel SwitchesManufacturer Robot Abbreviation Xxxx Robot TypeRobot Calibration Mode Schedule100 IPM 1000 IPM Robot Auto-Calibration Sample Programs Actual Motoman Welder Condition FileSample Auto-Calibration Routine For Motoman Robot Sample Auto-Calibration Routine For Fanuc Robot Sample Auto-Calibration Routine For ABB RobotWeld Data Pulse Reset ModeMild Steel Accu-pulse− Maintenance Routine MaintenanceBlowing Out Inside Of Unit Shock Hazard from testing − Safety Precautions for ServicingServicing Hazards Exploding Parts can cause injuryCalifornia Proposition 65 Warnings Set Value Mode − TroubleshootingDiagnostics Indicates a trigger closed error On errorIndicates RMD demo is done Indicates an overRemoving Cover and Measuring Input Capacitor Voltage Process Control Module PC4 Diagnostic LED’s Diagnostic LED’s On Process Control Module PC4Status Diagnosis Diagnostic LED’s On Wire Feed Module PC6 Diagnostic LED’s On User Interface Module PC7 User Interface Module PC7 Diagnostic LED’sAutomation Interface Module PC9 Diagnostic LED’s LED33LED32 Diagnostic LED’s On Automation Interface Module PC9 Input signal off from relay K6 for no arc detected Input signal on from relay K6 for arc detectedInput signal on for aux. relay energized Input signal off for aux. relay energizedModule Status LED’s Network And Module Status LED’s Network Status LED’sRed Circuit board is operating normallyTrouble Remedy TroubleshootingCircuit Diagram For Welding Power Source 1 − Electrical Diagrams198 992-G Part 1 Circuit Diagram For Welding Power Source 2 198 992-G Part 2 Circuit Diagram For 72 Pin Robot Interface 219 266-C Circuit Diagram For Peripheral/Motor Interface 219 267-B − Parts List 16 − Fig− Fig Windtunnel Assembly LH And RH Windtunnel Assembly LH And RH -1Item Top Tray Assembly Rear Panel Assembly Front Panel Assembly Description Quantity Page Page Service Your distributor also givesSupport Miller Electric Mfg. Co To locate a Distributor or Service Agency visitFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s