Miller Electric Auto Axcess 675 manual Diagnostic LED’s On Wire Feed Module PC6

Page 43

7-6. Wire Feed Module PC6 Diagnostic LED’s And Dip Switch Settings

	1 Wire Feed Module PC6
2	Diagnostic LED’s are visible inside
	unit, located on PC6 mounted on
	the top tray assembly.
	Refer to Section 7-7for information
	on diagnostic LED’s.
	Reinstall top cover after checking
1	diagnostic LED’s.
LED1 LED2	2 Dip Switch S1
	2 Dip Switch S1
	Dip switches are used to identify
	each circuit board on the internal
	network. Dip switch settings are
	different for each circuit board. For
	proper operation, do not change dip
	settings from those shown.

LED3

LED4

217 333-B / 803 300-A

7-7. Diagnostic LED’s On Wire Feed Module PC6

LED	Status	Diagnosis

1	On	Indicates +15 volts dc is present on wire feed module PC6

	Off	Indicates +15 volts dc is not present on wire feed module PC6

2	On	Indicates +5 volts dc is present on wire feed module PC6

	Off	Indicates +5 volts dc is not present on wire feed module PC6

3,4	On	See Network Status Table in Section 7-12

	Off	See Network Status Table in Section 7-12

OM-201 540 Page 39

Image 43

Contents File Advanced Manufacturing Systems OM-201 540KProcesses DescriptionFrom Miller to You Table of Contents Warranty HOT Parts can cause severe burns Symbol UsageArc Welding Hazards Electric Shock can killFlying Metal or Dirt can injure eyes Fumes and Gases can be hazardousARC Rays can burn eyes and skin Welding can cause fire or explosionMoving Parts can cause injury Welding Wire can cause injuryFire or Explosion hazard Falling Unit can cause injuryAbout Implanted Medical Devices Principal Safety StandardsCalifornia Proposition 65 Warnings EMF InformationUNE Décharge Électrique peut entraîner la mort Symboles utilisésLES Fumées ET LES GAZ peuvent être dangereux DES Pièces Chaudes peuvent provoquer des brûlures gravesLE Soudage peut provoquer un in cendie ou une explosion LA Chute DE L’APPAREIL peut blesser LE Bruit peut endommager l’ouïeLES Bouteilles peuvent exploser si elles sont endommagées Risque D’INCENDIE OU D’EXPLOLES Fils DE Soudage peuvent provoquer des blessures Proposition californienne 65 AvertissementsLE Soudage À L’ARC risque de provoquer des interférences Information EMF Principales normes de sécuritéEn ce qui concerne les implants médicaux OM-201 540 Specifications − InstallationDimensions And Weight Overheating Duty Cycle And OverheatingVolt-Ampere Curves 100% Duty Cycle At 675 AmperesDo not stack units. Beware of tipping Connection DiagramSelecting a Location Movement Do not move or operate TippingRear Panel Receptacles And Supplementary Protectors Incorrect Installation Connecting To Weld TerminalsSelecting Weld Cable Sizes Socket Information Peripheral Receptacle FunctionsMotor Control Receptacle Functions Normal Operating Electrical Service GuideHz Three Phase Input Voltage Input Amperes At Rated OutputWelding Power Source Input Power Connections Connecting Input PowerDisconnect Device Input Power Connections Program No Output a Output B Output C Remote Program SettingTouch Sensor Operation Remote Program SelectOperational Terms − OperationPostflow StartWeld CraterGas Type LED Wire Type LEDFront Panel Controls See Section Process LEDSTL Xxxx Robot Type Front Panel SwitchesRobot Abbreviations Manufacturer Robot AbbreviationSchedule Robot Calibration Mode100 IPM 1000 IPM Actual Motoman Welder Condition File Robot Auto-Calibration Sample ProgramsSample Auto-Calibration Routine For Motoman Robot Sample Auto-Calibration Routine For ABB Robot Sample Auto-Calibration Routine For Fanuc RobotWeld Data Accu-pulse Reset ModePulse Mild SteelRoutine Maintenance − MaintenanceBlowing Out Inside Of Unit Exploding Parts can cause injury − Safety Precautions for ServicingShock Hazard from testing Servicing HazardsCalifornia Proposition 65 Warnings Set Value Mode − TroubleshootingDiagnostics Indicates an over On errorIndicates a trigger closed error Indicates RMD demo is doneRemoving Cover and Measuring Input Capacitor Voltage Diagnostic LED’s On Process Control Module PC4 Process Control Module PC4 Diagnostic LED’sStatus Diagnosis Diagnostic LED’s On Wire Feed Module PC6 Diagnostic LED’s On User Interface Module PC7 User Interface Module PC7 Diagnostic LED’sLED33 Automation Interface Module PC9 Diagnostic LED’sLED32 Diagnostic LED’s On Automation Interface Module PC9 Input signal off for aux. relay energized Input signal on from relay K6 for arc detectedInput signal off from relay K6 for no arc detected Input signal on for aux. relay energizedCircuit board is operating normally Network And Module Status LED’s Network Status LED’sModule Status LED’s RedTrouble Remedy TroubleshootingCircuit Diagram For Welding Power Source 1 − Electrical Diagrams198 992-G Part 1 Circuit Diagram For Welding Power Source 2 198 992-G Part 2 Circuit Diagram For 72 Pin Robot Interface 219 266-C Circuit Diagram For Peripheral/Motor Interface 219 267-B 16 − Fig − Parts List− Fig Windtunnel Assembly LH And RH Windtunnel Assembly LH And RH -1Item Top Tray Assembly Rear Panel Assembly Front Panel Assembly Description Quantity Page Page Your distributor also gives ServiceSupport Your distributor and/or equipment manufacturer’s To locate a Distributor or Service Agency visitMiller Electric Mfg. Co For assistance in filing or settling claims, contact