Hitachi DH 25PB instruction manual Assembly and Operation, Applications, Prior to Operation

Page 10

English

ASSEMBLY AND OPERATION

APPLICATIONS

Rotation and striking function

◯Drilling anchor holes

◯Drilling holes in concrete

◯Drilling holes in tile

Rotation only function

◯Drilling in steel or wood (with optional accessories).

◯Tightening machine screws, wood screws (with optional accessories).

PRIOR TO OPERATION

1.Power source

Ensure that the power source to be utilized conforms to the power source requirements specified on the product nameplate.

2.Power switch

Ensure that the switch is in the OFF position. If the plug is connected to a receptacle while the switch is in the ON position, the power tool will start operating immediately and can cause serious injury.

3.Extension cord

When the work area is far away from the power source, use an extension cord of sufficient thickness and rated capacity. The extension cord should be kept as short as practicable.

WARNING:

Damaged cord must be replaced or repaired.

4.Check the receptacle

If the receptacle only loosely accepts the plug, the receptacle must be repaired. Contact a licensed electrician to make appropriate repairs.

If such a fautly receptacle is used, it may cause overheating, resulting in a serious hazard.

5.Confirming condition of the environment:

Confirm that the work site is placed under appropriate conditions conforming to prescribed precautions.

10

Image 10

Contents Advertencia AvertissementMartillo giratorio Table DES Matieres ContentsÍndice Important Safety Information Meanings of Signal WordsSafety General Safety RulesEnglish Specific Safety Rules and Symbols Never use a tool which is defective or operating abnormally Operate power tools at the rated voltageDo not wipe plastic parts with solvent Make Them Available to Other Users Owners of this Tool Double Insulation for Safer OperationFunctional Description SpecificationsName of Parts Applications Assembly and OperationPrior to Operation Selecting the driver bit Mounting the drill bit FigFront cap Part of SDS-plus shank Grip Drill bit Rotation + Striking HOW to USESwitch operation Rotation onlyWhen driving machine screws Fig When driving wood screws FigMounting hole Using the stopper FigUsing the side handle Cotter Taper shank adaptor RestsHow to bore Fig HOW to USE the Core BIT for Light LoadMounting Dismounting. Fig Inspecting the drill bits Maintenance and InspectionMaintenance of the motor Inspecting the screwsPower off and pull out the power plug How to replase greaseService and repairs Before replenishing the grease, turnAccessories Standard AccessoriesCotter Code No Chuck wrenchInner wedge type with the headless screw Large hole boring Rotation + Striking Guide Center pin Core bit Shank PlateOn the market Wrench Code NoPhillips Driver Bit Informations Importantes DE Sécurité Signification DES Mots D’AVERTISSEMENTRegles Generale DE Securite SecuriteConserver CES Instructions Français Regles DE Securite Specifiques ET Symboles NE Jamais toucher les parties mobilesUtiliser l’outil motorisé à la tension nominale Garder propres les évents d’air du moteurNe pas essuyer les parties en plastique avec du solvant Double Isolation Pour UN Fonctionnement Plus SUR NOM DES Parties Description FonctionnellePoids Lbs 3,4 kg Assemblage ET Fonctionnement Avant L’UTILISATIONMontage du foret de perçage Fig Godet à poussière Collecteur à poussière BFonctionnement de l’interrupteur UtilisationSélection de la mèche pour visseuse Rotation + frappeLors du vissage des vis machine Fig Rotation seulementMèche Enfoncement de vis à bois Fig Utilisation de l’arràtoir FigUtilisation de la poignée latérale Perçage Fig Démontage FigInspection des vis Entretien ET InspectionContrôle du foret de perçage Entretien du moteurComment remplacer la graisse Entretien et reparationAccessoires Accessoires StandardClavette No. de code Clé de mandrinType à cale intérieure avec vis sans tête Plaque centrale de guidage Français Embout de vissage Phillips Información Importante Sobre Seguridad Significado DE LAS Palabras DE SeñalizaciónNormas Generales DE Seguridad SeguridadGuarde Estas Instrucciones Español No toque Nunca las piezas móviles Normas Y Símbolos Específicos DE SeguridadUtilice la herramienta correcta Maneje con cuidado las herramientas eléctricas Maneje correctamente la herramientaNo limpie las partes de plástico con disolvente Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Español Especificaciones Descripción FuncionalNomenclatura Peso Lbs 3,4 kgAplicaciones Montaje Y OperaciónAntes DE LA Operación Montaje de la broca Fig Capa de polvo Colector de polvo BOperación del conmutador Como SE USASelección de la broca destornillador Rotación + golpeteoRotación solamente Cuando coloque tornillos para metal FigAtornillando tornillos para madera Fig Modo de usar el tope FigMontaje Modo DE Usar LA Barrena Tubularpara Cargas LigerasUso del asa lateral ApoyoPlaca guía Modo de taladrar FigConectar el enchufe a la toma de alimentación Pasador Punta de Central Barrena tubular TubularDesmontaje Fig Inspección de los tornillos Mantenimiento E InspecciónInspeccionar la broca de taladro Mantenimiento de motorCambio de grasa Mantenimiento y reparaciónAccesorios Accesorios EstándarLiave de portabrocas Tipo de reborde interior con tornillo sin cabeza Placa guia Español Broca para tornillos Plillips Page Kestrel Road Mississauga on L5T 1Z5

Related manuals

Manual 7 pages 54.2 Kb