Hitachi DH 25PB instruction manual Make Them Available to Other Users Owners of this Tool

Page 8

English

DOUBLE INSULATION FOR SAFER OPERATION

To ensure safer operation of this power tool, HITACHI has adopted a double insulation design. “Double insulation “ means that two physically separated insulation systems have been used to insulate the electrically conductive materials connected to the power supply from the outer frame handled by the operator. Therefore, either the symbol “” or the words “Double insulation” appear on the power tool or on the nameplate.

Although this system has no external grounding, you must still follow the normal electrical safety precautions given in this Instruction Manual, including not using the power tool in wet environments.

To keep the double insulation system effective, follow these precautions:

◯Only HITACHI AUTHORIZED SERVICE CENTER should disassemble or assemble this power tool, and only genuine HITACHI replacement parts should be installed.

◯Clean the exterior of the power tool only with a soft cloth moistened with soapy water, and dry thoroughly.

Never use solvents, gasoline or thinners on plastic components; otherwise the plastic may dissolve.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO

OTHER USERS

AND

OWNERS OF THIS TOOL!

8

Image 8

Contents Martillo giratorio AvertissementAdvertencia Índice ContentsTable DES Matieres Important Safety Information Meanings of Signal WordsSafety General Safety Rules English Specific Safety Rules and Symbols Do not wipe plastic parts with solvent Operate power tools at the rated voltageNever use a tool which is defective or operating abnormally Make Them Available to Other Users Owners of this Tool Double Insulation for Safer OperationName of Parts SpecificationsFunctional Description Prior to Operation Assembly and OperationApplications Front cap Part of SDS-plus shank Grip Drill bit Mounting the drill bit FigSelecting the driver bit HOW to USE Switch operationRotation + Striking Rotation onlyWhen driving machine screws Fig When driving wood screws FigUsing the stopper Fig Using the side handleMounting hole Cotter Taper shank adaptor RestsMounting HOW to USE the Core BIT for Light LoadHow to bore Fig Dismounting. Fig Maintenance and Inspection Maintenance of the motorInspecting the drill bits Inspecting the screwsHow to replase grease Service and repairsPower off and pull out the power plug Before replenishing the grease, turnAccessories Standard AccessoriesCotter Code No Chuck wrenchInner wedge type with the headless screw Large hole boring Rotation + Striking Guide Center pin Core bit Shank PlateOn the market Wrench Code NoPhillips Driver Bit Informations Importantes DE Sécurité Signification DES Mots D’AVERTISSEMENTConserver CES Instructions SecuriteRegles Generale DE Securite Français Regles DE Securite Specifiques ET Symboles NE Jamais toucher les parties mobilesNe pas essuyer les parties en plastique avec du solvant Garder propres les évents d’air du moteurUtiliser l’outil motorisé à la tension nominale Double Isolation Pour UN Fonctionnement Plus SUR Poids Lbs 3,4 kg Description FonctionnelleNOM DES Parties Assemblage ET Fonctionnement Avant L’UTILISATIONMontage du foret de perçage Fig Godet à poussière Collecteur à poussière BUtilisation Sélection de la mèche pour visseuseFonctionnement de l’interrupteur Rotation + frappeMèche Rotation seulementLors du vissage des vis machine Fig Enfoncement de vis à bois Fig Utilisation de l’arràtoir FigUtilisation de la poignée latérale Perçage Fig Démontage FigEntretien ET Inspection Contrôle du foret de perçageInspection des vis Entretien du moteurComment remplacer la graisse Entretien et reparationAccessoires Accessoires StandardClavette No. de code Clé de mandrinType à cale intérieure avec vis sans tête Plaque centrale de guidage Français Embout de vissage Phillips Información Importante Sobre Seguridad Significado DE LAS Palabras DE SeñalizaciónGuarde Estas Instrucciones SeguridadNormas Generales DE Seguridad Español Utilice la herramienta correcta Normas Y Símbolos Específicos DE SeguridadNo toque Nunca las piezas móviles No limpie las partes de plástico con disolvente Maneje correctamente la herramientaManeje con cuidado las herramientas eléctricas Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Español Descripción Funcional NomenclaturaEspecificaciones Peso Lbs 3,4 kgAntes DE LA Operación Montaje Y OperaciónAplicaciones Montaje de la broca Fig Capa de polvo Colector de polvo BComo SE USA Selección de la broca destornilladorOperación del conmutador Rotación + golpeteoRotación solamente Cuando coloque tornillos para metal FigAtornillando tornillos para madera Fig Modo de usar el tope FigModo DE Usar LA Barrena Tubularpara Cargas Ligeras Uso del asa lateralMontaje ApoyoModo de taladrar Fig Conectar el enchufe a la toma de alimentaciónPlaca guía Pasador Punta de Central Barrena tubular TubularDesmontaje Fig Mantenimiento E Inspección Inspeccionar la broca de taladroInspección de los tornillos Mantenimiento de motorCambio de grasa Mantenimiento y reparaciónAccesorios Accesorios EstándarLiave de portabrocas Tipo de reborde interior con tornillo sin cabeza Placa guia Español Broca para tornillos Plillips Page Kestrel Road Mississauga on L5T 1Z5

Related manuals

Manual 7 pages 54.2 Kb