Hitachi DH 25PB instruction manual Important Safety Information, Meanings of Signal Words

Page 3

English

IMPORTANT SAFETY INFORMATION

Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual before operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it occurs, and by observing appropriate safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and in the sections which contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identified by WARNINGS on the power tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been specifically recommended by

HITACHI.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate injury, or may cause machine damage.

NOTE emphasizes essential information.

3

Image 3
Contents Avertissement AdvertenciaMartillo giratorio Contents Table DES MatieresÍndice Meanings of Signal Words Important Safety InformationGeneral Safety Rules SafetyEnglish Specific Safety Rules and Symbols Operate power tools at the rated voltage Never use a tool which is defective or operating abnormallyDo not wipe plastic parts with solvent Double Insulation for Safer Operation Make Them Available to Other Users Owners of this ToolSpecifications Functional DescriptionName of Parts Assembly and Operation ApplicationsPrior to Operation Mounting the drill bit Fig Selecting the driver bitFront cap Part of SDS-plus shank Grip Drill bit Rotation only HOW to USESwitch operation Rotation + StrikingWhen driving wood screws Fig When driving machine screws FigCotter Taper shank adaptor Rests Using the stopper FigUsing the side handle Mounting holeHOW to USE the Core BIT for Light Load How to bore FigMounting Dismounting. Fig Inspecting the screws Maintenance and InspectionMaintenance of the motor Inspecting the drill bitsBefore replenishing the grease, turn How to replase greaseService and repairs Power off and pull out the power plugStandard Accessories AccessoriesChuck wrench Cotter Code NoInner wedge type with the headless screw Core bit Shank Plate Large hole boring Rotation + Striking Guide Center pinWrench Code No On the marketPhillips Driver Bit Signification DES Mots D’AVERTISSEMENT Informations Importantes DE SécuritéSecurite Regles Generale DE SecuriteConserver CES Instructions Français NE Jamais toucher les parties mobiles Regles DE Securite Specifiques ET SymbolesGarder propres les évents d’air du moteur Utiliser l’outil motorisé à la tension nominaleNe pas essuyer les parties en plastique avec du solvant Double Isolation Pour UN Fonctionnement Plus SUR Description Fonctionnelle NOM DES PartiesPoids Lbs 3,4 kg Avant L’UTILISATION Assemblage ET FonctionnementGodet à poussière Collecteur à poussière B Montage du foret de perçage FigRotation + frappe UtilisationSélection de la mèche pour visseuse Fonctionnement de l’interrupteurRotation seulement Lors du vissage des vis machine FigMèche Utilisation de l’arràtoir Fig Enfoncement de vis à bois FigUtilisation de la poignée latérale Démontage Fig Perçage FigEntretien du moteur Entretien ET InspectionContrôle du foret de perçage Inspection des visEntretien et reparation Comment remplacer la graisseAccessoires Standard AccessoiresClé de mandrin Clavette No. de codeType à cale intérieure avec vis sans tête Plaque centrale de guidage Français Embout de vissage Phillips Significado DE LAS Palabras DE Señalización Información Importante Sobre SeguridadSeguridad Normas Generales DE SeguridadGuarde Estas Instrucciones Español Normas Y Símbolos Específicos DE Seguridad No toque Nunca las piezas móvilesUtilice la herramienta correcta Maneje correctamente la herramienta Maneje con cuidado las herramientas eléctricasNo limpie las partes de plástico con disolvente Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Español Peso Lbs 3,4 kg Descripción FuncionalNomenclatura EspecificacionesMontaje Y Operación AplicacionesAntes DE LA Operación Capa de polvo Colector de polvo B Montaje de la broca FigRotación + golpeteo Como SE USASelección de la broca destornillador Operación del conmutadorCuando coloque tornillos para metal Fig Rotación solamenteModo de usar el tope Fig Atornillando tornillos para madera FigApoyo Modo DE Usar LA Barrena Tubularpara Cargas LigerasUso del asa lateral MontajePasador Punta de Central Barrena tubular Tubular Modo de taladrar FigConectar el enchufe a la toma de alimentación Placa guíaDesmontaje Fig Mantenimiento de motor Mantenimiento E InspecciónInspeccionar la broca de taladro Inspección de los tornillosMantenimiento y reparación Cambio de grasaAccesorios Estándar AccesoriosLiave de portabrocas Tipo de reborde interior con tornillo sin cabeza Placa guia Español Broca para tornillos Plillips Page Kestrel Road Mississauga on L5T 1Z5
Related manuals
Manual 7 pages 54.2 Kb