Hitachi DH 38YE Extension cord, Check the receptacle, Confirming condition of the environment

Page 14

English

3.Extension cord

When the work area is far away from the power source, use an extension cord of sufficient thickness and rated capacity. The extension cord should be kept as short as practicable.

WARNING: Damaged cord must be replaced or repaired.

4.Check the receptacle

If the receptacle only loosely accepts the plug, the receptacle must be repaired. Contact a licensed electrician to make appropriate repairs.

If such a fautly receptacle is used, it may cause overheating, resulting in a serious hazard.

5.Confirming condition of the environment:

Confirm that the work site is placed under appropriate conditions conforming to prescribed precautions.

6.How to install dust cover (Fig. 2)

Always install the dust cover on the drill bit or the taper shank adaptor. Insert the dust cover until it lies flush in the groove.

NOTE: For a thick drill bit, insert the dust cover from drill rear.

7.How to install tool

CAUTION: For tools such as a bull point and a cold chisel, use only Hitachi genuine parts.

(1)Clean, then smear the tool shank with the grease provided.

(2)Pull the tool holder in the direction of arrow 1 and rotate it in the direction of arrow 2 (counterclockwise). Fully insert the tool shank into the hexagonal hole of the front cover. (Fig. 3)

(3)Return the tool holder to fix the tool.

NOTE: Remove in the reverse order to installation.

Insert up to the groove

Dust cover

Fig. 2

Front Cover

Tool Shank

Tool Holder

Fig. 3

14

Image 14

Contents Avertissement Rotary Hammer Marteau Rotatif Martillo GiratorioContents Meanings of Signal Words Important InformationNever Operate Without ALL Guards in Place Keep Work Area CleanNever Touch Moving Parts Always Wear EYE and EAR ProtectorDON’T Force Tool Remove Adjusting Keys and WrenchesKeep Children Away USE Right ToolOperate Power Tools AT the Rated Voltage Check for Live WiresKeep Motor AIR Vent Clean Carefully Handle Power ToolsPolarized Plugs Important Safety Instructions For USE of the Rotary HammerReplacement Parts USE of Extension Cord Double Insulation for Safer Operation Specifications Name of PartsPage Page Applications Power sourcePower switch Prior to OperationExtension cord How to install dust cover FigHow to install tool Check the receptacleHow to chisel or crush Fig HOW to USEHow to drill holes Fig How to select rotation-hammering Hammering. FigHow to use stopper How to bore Fig MountingDismounting Fig HOW to Replase GreaseGrease replacement period Grease replenishmentInspecting the drill bits Maintenance and InspectionMaintenance of the motor Inspecting the mounting screwsService and Repairs Informations Importantes Signification DES Mots D’AVERTISSEMENTLire Tout CE Mode D’EMPLOI NE PAS Forcer L’OUTIL Considerer L’ENVIRONNEMENT DE L’AIRE DE TravailEloigner LES Enfants Utiliser L’OUTIL CorrectVerifier S’IL Y a DES Pieces Endommagees Cordons DE Rallonge Pour Utilisation a L’EXTERIEURRester SUR SES Gardes Manipuler L’OUTIL CorrectementNE PAS Essuyer LES Parties EN Plastique Avec DU Solvant Manipuler L’OUTIL Motorise Avec PrecautionUtiliser L’OUTIL Motorise a LA Tension Nominale Pieces DE Rechange Fiches PolariseesUtilisation D’UN Cordon DE Rallonge Double Isolation Pour UN Fonctionnement Plus SUR NOM DES Parties RemarquePage Page Interrupteur d’alimentation Avant L’UTILISATIONSource d’alimentation Cordon prolongateurUtilisation Comment installer le cache-poussière FigComment installer l’outil Vérification des conditions d’environnementUtilisation de la quenouille Comment buriner ou broyer FigComment sélectionner rotation-percussion et percussion Fig Perçage Fig Comment Utiliser LA CouronneMontage Démontage Fig Période de remplacementComment Remplacer LA Graisse Plein de graisseInspection des vis de montage Entretien ET InspectionContrôle du foret de perçage Entretien du moteurEntretien ET Reparation Información Importante Significado DE LAS Palabras DE SeñalizaciónLEA Todas LAS Instrucciones Utilice LA Herramienta Correcta Mantenga a LOS Niños AlejadosNo Fuerce LAS Herramientas 13. Vístase AdecuadamentePreste Atención Quite LAS Llaves DE AjusteUtilice Adecuadamente UN Cable Prolongador EN Exteriores Compruebe LAS Piezas DañadasNo Limpie LAS Partes DE Plástico CON Disolvente Mantenga Limpio EL Conducto DE Ventilación DEL MotorManeje CON Cuidado LAS Herramientas Eléctricas Utilice Solamente Piezas DE Reemplazo Genuinas DE HitachiPiezas DE Reemplazo Enchufes PolarizadosUtilización DE UN Cable Prolongador Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Nota NomenclaturaEspecificaciones Page Page Aplicaciones Antes DE LA OperaciónMontaje de la herramienta Confirme las condiciones del medio ambienteInstalación de la cubierta para polvo Fig Taladrar orificios FigPrecaución Selección de rotación-martilleo y martilleo FigCómo usar el tope Ponga en on el interruptor de alimentación y Montaje Modo de taladrar FigPeríodo de cambio de grasa Cambio DE GrasaDesmontaje Fig Rellenado de grasaInspección de los tornillos de montaje Mantenimiento E InspecciónInspeccionar la broca de taladro Mantenimiento de motorMantenimiento Y Reparación Page Page Page Page Page Page Hitachi Koki Canada Co