Hitachi G 23MR, G 18MR instruction manual Service and repairs, Service parts list

Page 16

English

(2)Use the auxiliary hexagonal wrench or small screwdriver to pull up the edge of the spring that is holding down the carbon brush. Remove the edge of the spring toward the outside of the brush holder.

(3)Remove the end of the pig-tail on the carbon brush from the terminal section of brush holder and then remove the carbon brush form the brush holder.

<Assembly>

(1)Insert the end of the pig-tail of the carbon brush in the terminal section of brush holder.

(2)Insert the carbon brush in the brush holder.

(3)Use the auxiliary hexagonal wrench or small screwdriver to return the edge of the spring to the head of the carbon brush.

(4)Mount the tail cover and tighten the D4 tapping screw.

5.Service and repairs

All quality power tools will eventually require servicing or replacement of parts because of wear from normal use. To assure that only authorized replacement parts will be used, all service and repairs must be performed by a HITACHI AUTHORIZED SERVICE CENTER, ONLY.

6.Service parts list

A:Item No.

B:Code No.

C:No. Used

D:Remarks

CAUTION:

●Repair, modification and inspection of Hitachi Power Tools must be carried out by a Hitachi Authorized Service Center.

This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance.

In the operation and maintenance of power tools, the safety regulations and standards prescribed in each country must be observed.

MODIFICATIONS: Hitachi Power Tools are constantly being improved and modified to incorporate the latest technological advancements.

Accordingly, some parts (i.e. code numbers and/or design) may be changed without prior notice.

16

Image 16

Contents Advertencia AvertissementAmoladora angular Table DES Matieres ContentsÍndice Important Safety Information Meanings of Signal WordsSafety General Safety RulesEnglish Never operate without all guards in place Specific Safety Rules and SymbolsUse right tool Blades and accessories must be securely mounted to the tool Keep motor air vent cleanOperate power tools at the rated voltage Handle tool correctlyDouble Insulation for Safer Operation Make Them Available to Other Users and Owners of this Tool Functional Description SpecificationsName of Parts Applications Assembly and OperationPrior to Operation Use only properly rated depressed center wheels Mounting the wheel guardCheck the push button Grinder Operation Assembly Depressed Center Wheel Assembly and DisassemblyDisassembly Maintenance and Inspection Replacing the depressed center wheelInspecting the screws Inspecting the carbon brushes FigService and repairs Service parts listAccessories Standard AccessoriesInformations Importantes DE Sécurité Signification DES Mots D’AVERTISSEMENTSecurite Regles Generale DE SecuriteConserver CES Instructions Avertissement Lire et coxmprendre toutes les instructionsFrançais Regles DE Securite Specifiques ET Symboles Garder propres les évents d’air du moteur Utiliser l’outil motorisé à la tension nominaleNe pas essuyer les parties en plastique avec du solvant Double Isolation Pour UN Fonctionnement Plus SUR Description Fonctionnelle NOM DES PartiesUtilisations Avant L’UTILISATIONMontage du capot couvre-meule 6600 t/mn ou plusUtilisation DE LA Meuleuse Assemblage Opération d’ajustement pour la finition souhaitéeDéassemblage Remplacement de la meule à dépression centrale Entretien ET InspectionInspection des vis Inspection des balais en carbone FigEntretien et réparation Liste des pièces de rechangeAccessoires Standard AccessoiresAccessoires SUR Option Información Importante Sobre Seguridad Significado DE LAS Palabras DE SeñalizaciónSeguridad Normas Generales DE SeguridadGuarde Estas Instrucciones Advertencia Lea y entienda todas las instruccionesEspañol Normas Y Símbolos Específicos DE Seguridad Maneje correctamente la herramienta Utilice la herramienta correctaManeje con cuidado las herramientas eléctricas No limpie las partes de plástico con disolvente Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Nomenclatura Descripción FuncionalEspecificaciones Aplicaciones Montaje Y OperaciónAntes DE LA Operación Utilice ruedas de disco abombado de la capacidad apropiada Montaje del protector de la ruedaRPM o más Operación DE LA Amoladora Angular Compruebe el botón pulsadorConecte la alimentación de la amoladora Fig Presione con poca fuerza la amoladoraMontaje Y Desmontaje DE LA Rueda DE Disco Abombado Mueva la amoladora en el sentido apropiadoAjuste la operación de acuerdo con el acabado deseado ArmadoDesarmado Mantenimiento E Inspección Reemplazo de la rueda de disco abombadoInspección de los tornillos Inspección de la escobillas FigMantenimiento y reparación Lista de repuestosAccesorios Estándar AccesoriosAccesorios Opcionales Page 6301DDCMPS2L G23MR 6200VVCMPS2L Hitachi Koki Canada Co