Bosch Power Tools 1812PSD, 1811PSD, 1810PSD manual BM 1609929J65 02-08 2/20/08 1130 AM

Page 4

BM 1609929J65 02-08 2/20/08 11:30 AM Page 4

Hold tool by insulated gripping surfaces when performing an operation where the cutting tools may contact hidden wiring or its own cord. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator.

Always use auxiliary handle for maximum control over torque reaction or kick-back.

Operation of the grinder without the side handle could cause loss of control of the grinder, resulting in possible serious personal injury.

Before using a grinder or installing a new wheel, inspect the grinding wheel for chips and cracks. Remove bad wheels immediately. Run the tool at no load for one minute, holding the tool in the direction away from people. Wheels with flaws will normally break apart during this time.

Carefully handle both the tool and individual grinding wheels to avoid chipping or cracking. Install a new wheel if tool is dropped while grinding. Do not use a wheel that may be damaged.

Fragments from a wheel that bursts during operation will fly away at great velocity possibly striking you or bystanders.

Do not use grinding wheel that is larger than the maximum recommended size for your tool, or worn down damaged wheels from larger grinders. Wheels intended for large angle sander/grinders are not suitable for the high speed of a small angle sander/grinder, these wheels may easily burst and the fragments strike you or bystanders.

Do not use depressed hub grinding wheels for cut-off operations. Depressed hub wheels or type 27 wheels are not intended for side loading and may shatter under overload.

Do not use this tool with “Woodcarving” blade. Such blades create frequent kick-back and loss of control.

Wear proper apparel while using a sander/grinder. Face shield or at least safety goggles, dust mask, leather gloves and shop apron capable of stopping small wheel or workpiece fragments.

Position the cord clear of the spinning grinding wheel or any other sanding

accessory. Do not wrap the cord around your arm or wrist. If you lose control and have the cord wrapped around your arm or wrist it may entrap you and cause injury.

Avoid bouncing and snagging the wheel, especially when working corners, sharp edges etc. This can cause loss of control and kick-back.

Regularily clean the tool’s air vents by compressed air. Excessive accumulation of powdered metal inside the motor housing may cause electrical failures.

Do not grind or sand near flammable materials. Sparks from the wheel could ignite these materials.

This tool can be converted to a sander. When grinding is resumed the proper guard and wheel flanges MUST be reinstalled before proceeding with grinding. The guard must always be attached to the tool and positioned for maximum safety, so the least amount of wheel is exposed from the side the tool is being operated. The grinding wheel guard cannot be used for most sanding operations or for wire brushing.

When sanding, do not use oversized sanding disc. Larger sanding disc will extend beyond the sanding pad causing snagging, tearing of the disc or kick-back. Extra paper extending beyond the sanding pad can also cause serious lacerations.

!WARNING Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

Lead from lead-based paints,

Crystalline silica from bricks and cement and other masonry products, and

Arsenic and chromium from chemically- treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

-4-

Image 4
Contents Read Before Using General Power Tool Safety Warnings Work area safetyElectrical safety Personal safetyAngle Grinder Safety Rules Power tool use and careService Many accidents are caused by poorly maintained power toolsBM 1609929J65 02-08 2/20/08 1130 AM Symbols Symbol Name Designation/ExplanationFunctional Description and Specifications Spindle Lock Paddle Switch Grinding WheelAngle Grinders Measures reduce the risk of starting the tool accidentallyAssembly Disc Grinding Wheel Assembly Sanding Accessories AssemblyOperating Instructions Grinding OperationsSanding Operations Selecting Sanding DiscSanding Tips Sanding WoodMaintenance Wire Brush OperationsCleaning AccessoriesExtension Cords Sécurité électrique Sécurité du lieu de travailSécurité personnelle Consignes de sécurité de la rectifieuse dangle Utilisation et entretien des outils ÉlectroportatifsEntretien Instable et risque de résulter en une perte de contrôleLe plomb provenant des peintures à base de plomb Symboles Symbole Nom Désignation/ExplicationDescription fonctionnelle et spécifications Rectifieuses d’anglesInterrupteur Palette Poignée Latérale Filet darbre Po -11 UNC Po 11 UNCAssemblage Ensemble de meule à disqueDE Meule Type Bride Dappui Arbre Protecteur DE Disque D’APPUIEnsemble DE Brosse Métallique Arbre Disque ’APPUI Disque DE PonçageConsignes de fonctionnement Travaux de meulageTravaux de ponçage Soudaine sur la meuleChoix DES Disques DE Ponçage Ponçage DU BoisEntretien Travaux à la brosse métalliqueAccessoires Cordons de rallongeNettoyage Certains AgentsSeguridad eléctrica Seguridad del área de trabajoSeguridad personal Mecánicas Normas de seguridad para amoladoras angularesServicio de ajustes y reparaciones Podría causar pérdida de control Símbolos Símbolo Nombre Designación/explicaciónCon aislamiento doble De Li-ionDescripción funcional y especificaciones Amoladoras angularesInterruptor DE Paleta Mango Lateral Control DE LAEnsamblaje Mango LateralModelos 1810PD, 1810PSD, 1811PS y Rueda DE Amolar DE Tipo PestañaTipo Pestaña DE Soporte Protector DE LA Muela Tipo Rueda DE Amolar DE Disco Tuerca DE FijaciónZapata DE Soporte EL Disco DE LijarInstrucciones de funcionamiento Operación de amoladoOperaciones de lijado Seleccion DEL Disco DE LijarConsejos Para Lijar Lijado DE MaderaOperaciones con escobillas de alambre MantenimientoServicio Cordones de extensión AccesoriosLimpieza Para evitarRemarques Notas Limited Warranty of Bosch Portable and Benchtop Power Tools
Related manuals
Manual 52 pages 16.19 Kb