Parts List, Description | Harbor Freight Tools 95668 specification

PARTS LIST

Part #	Description	Part #	Description
1	Side Panel	59	Fence Body (Left)
2	Tie Bar	60	Fence
3	Rubber Foot	61	Lock Handle
4	Philips Head Screw (M4-0.7x25)	62	Flat Washer (1/2”)
5	Power Switch	63	Flat Washer (3/8”)
6	Switch Lamella	64	Knob (M8-1.25)
7	Flat Washer (5mm)	65	Lock Washer (1/2”)
8	Hex Nut (M4-0.7)	66	Hex Bolt (M12-1.75 x 20)
9	Carriage Bolt (M8-1.25 x 12)	67	Adjusting Screw Stud
10	Flat Washer (3/8”)	68	Hand Knob
11	Hex Nut (M8-1.25)	69	Roll Pin (3 x 20)
12	Philips Head Screw (M5-0.8 x 12)	70	Philips Head Screw (M6-1 x 12)
13	Exterior Tooth Washer (5mm)	71	Half Collar
14	Hex Nut (M5-0.8)	72	Adjusting Shaft
15	Shelf	73	Flat Washer (1/2”)
16	Electricity Label	74	Hex Nut (M12-1.75)
		75	Hex Bolt (M8-1.25 x 12)
18	Hex Nut (M8-1.25)	76	Flat Washer (3/8”)
19	Flat Washer (3/8”)	77	Hold Down Bar
20	Strain Relief	78	Philips Head Screw (M4-0.7 x 10)
21	Spindle Pulley Guard	79	Hex Post
22	Power Cord	80	Hex Nut (M8-1.25)
23	Wire Cord	81	Flat Washer (3/8”)
		82	Mounting Bracket
		83	Hand Knob
26	Flat Washer (3/8”)	84	Hex Nut (M4-0.7)
27	Hex Bolt (M8-1.25 x 12)	85	Ring Guard
28	Table Leg	86	Hex Bolt (M8-1.25 x 30)
		87	Housing Bracket
30	Hex Bolt (M8-1.25 x 25)	88	Clamp Sleeve (Left)
31	Hex Bolt (M12-1.75 x 30)	89	Stuff Ring
32	Lock Washer (12mm)	90	Roll Pin (3 x 20mm)
33	Table Support	91	Lock Bar
34	Miter Block	92	Hand Knob
35	Flat Washer (1/4”)	93	Roll Pin (3 x 20mm)
36	Philips Head Screw (M4-0.7 x 6)	94	Lock Nut
37	Self Tapping Screw (3.5 x 12mm)	95	Hex Bolt (M12-1.75 x 30)
38	Flat Washer (3/8”)	96	Upper Spindle Nut
39	Support Pole	97	Safety Washer
40	Stud Bolt	98	Rub Collar (1/2” x 1-3/16” x 3/16”)
41	Anti-Kickback Pin	99	Rub Collar (1/2” x 1-3/16” x 1/4”)
42	Miter Bar	100	Rub Collar (1/2” x 1-3/16” x 3/8”)
43	Aluminum Alloy Fence	101	Cutter Spindle
44	Right Fence Lid	102	Collet Nut
44A	Left Fence Lid	103	Collet
45	Miter Gauge Body	104	Collet
46	Plastic Handle	105	Spindle
47	Pointer	106	Key (4 x 4 x 20mm)
48	Self Tapping Screw (M3 x 15)	107	Interior Retaining Ring (47mm)
49	Tension Pin (2 x 16mm)	108	Wave Washer (45mm)
50	Carriage Bolt (M6-1 x 35)	109	Ball Bearing
51	Knob (M6-1.0)	110	Spindle Housing
52	Work Table	111	Ball Bearing Sleeve
53	Table Insert (1-3/8” Hole)	112	Ball Bearing
53A	Table Insert (1-3/4” Hole)	113	Spindle Pulley
54	Carriage Bolt (M6-1 x 35)	114	Lower Spindle Nut
55	Knob (M6-1.0)	115	Bearing Cone
56	Taper Pin (8 x 75mm)	116	Coil Spring
57	Fence Body (Right)	117	Set Screw (M8-1.25 x 8)
58	Clamp Stud	118	Spring Collar

NOTE:

Some parts are listed and shown for illustration purposes only,

and are not available individually as replacement parts.

SKU 95668

For technical questions, please call 1-800-444-3353

PAGE 27