Harbor Freight Tools 95668 operating instructions Wiring Diagram, Motor

Page 28

PARTS LIST (CONT.)

Part #	Description	Part #	Description
119	Stud	134	Hex Head Screw (M12-1.75 x 35)
120	Knob	135	Flat Washer (1/2”)
121	Draw Bar (M8-1.0)	136	Motor Mount Plate
122	Draw Bar Hex Nut (M8-1.0)	137	Flat Washer (3/8”)
123	Belt (690 x 10mm)	138	Hex Nut (M8-1.25)
124	Hex Bolt (M8-1.25 x 12)	139	Lock Washer (12mm)
125	Flat Washer (3/8”)	140	Lock Washer (8mm)
126	Belt Guard	141	Flat Washer (1/4”)
127	Motor Pulley	142	Shim
128	Set Screw (M6-1 x 10)	143	Philips Head Screw (M6-1 x 12)
129	Motor	144	Forward/Reverse Switch
129-1	Start Capacitor	145	Switch Bracket
129-2	Capacitor Cover	146	Arbor Wrench
129-3	Wiring Box	147	Tap Screw (M3.5 x 12)
129-4	Motor Fan	148	Right Fence Lid
129-5	Motor Fan Cover	149	Left Fence Lid
130	Key (5 x 5 x 22mm)	150	1/2” Spacer
131	Carriage Bolt (M8-1.25 x 40)	151	Long Hex Bolt M12 x 1.75 x 40

132	Lock Washer (8mm)	152	Short Hex Bolts M12 x 1.75 x 30
133	Flat Washer (3/8”)

WIRING DIAGRAM

Disconnect power from machine before performing any electri- cal service. Failure to do this will result in a shock hazard leading to injury.

	MOTOR	GREEN
	MOTOR	BLACK	WHITE
	GREEN	POWER
BLACK	WHITE	SWITCH
BLACK	WHITE

CAPACITOR

WHITE BLACK

		BLACK
	BLACK	WHITE
	WHITE	WHITE
	WHITE
	RED
	FWD/REV SWITCH	REAR VIEW
	FWD/REV SWITCH	OF SWITCH
		OF SWITCH
		REAR VIEW
		OF SWITCH

REV 07j

SKU 95668

For technical questions, please call 1-800-444-3353

PAGE 28

Image 28

Contents For technical questions or replacement parts, please call Industrial SHAPER/ROUTERProduct Specifications General Safety RulesSave this Manual Work AreaElectrical Safety Tool USE and Care Specific Safety Rules ServicePage Grounding Prong Plug and Outlet Outlets for 2-Prong Plug See 3-Prong Plug and OutletSee Outlets for 2-Prong Plug Assembly Instructions Stand AssemblyUnpacking See Figure FOptional Table Spacer Installation See Figure GInstalling The Fences Installing The Safety GuardInstalling The Spindle 57, 59. See Figure HHex Nut. See Figure M Figure JAdjustments Instructions Router Bit AssemblySee Figures K, L, and M See Figure OFence Alignment See Figure P57, 59. See Figure Q Belt Adjustment Table InsertsSee Figure R Screws. See Figure SCutter Direction Cutter InstallationSee Figure T Setting Spindle Height See Figure Y, nextRub Collars See Figure AAOperating Instructions Cutter. See Figure CCTo Set Up The Wooden Fences For Straight Shaping Start UpSee Figure DD Figure DDTo Set Up The Aluminum Fences For Partial Edge Removal Freehand ShapingSee Figures HH Figure HHPattern Shaping See Figure JJINSPECTION, MAINTENANCE, and Cleaning Please Read the Following CarefullyTroubleshooting Problem Possible Reason Possible SolutionParts List DescriptionWiring Diagram MotorAssembly Diagram Limited 1 year / 90 Day warranty Mission Oaks Blvd. PO Box 6009 Camarillo, CA 93011 800