Compatible Systems 1220I manual Telco Line Connection Requirements, Interface

Page 13

Chapter 2 - Getting Started

7

 

 

10Base-T Twisted-Pair Ethernet

To connect the router's Ethernet interface to twisted-pair Ethernet cabling you will need an unshielded twisted-pair station cable that is connected to a 10BaseT-compatible twisted-pair hub.

Note: Ethernet cables and cable connectors are not supplied with vthe MicroRouter product. Please contact your reseller or your Compatible Systems representative for information on obtaining the correct Ethernet cabling supplies.

Telco Line Connection Requirements

In order to connect to non-T1 wide area transmission lines, you must connect the router’s secondary wide area port to a modem, 56K CSU/DSU, or ISDN Terminal Adapter. Which of these devices you use depends on the type of telco line.

Note: Before attempting to connect the MicroRouter 1220i to a vleased telco line, use the loopback features of your CSU/DSU to check the line. This can save you a considerable amount of time, since the more equipment you have on the line, the more difficult it becomes to determine where a problem is occurring.

The MicroRouter 1220i provides one high-speed V.35 synchronous interface, and one RS-232 sync/async interface, each of which can be independently configured for PPP, Frame Relay or SMDS operation. The V.35 interface is capable of communicating to another router or a PPP client machine over a 56K CSU/DSU, an ISDN Terminal Adapter, or a T1 CSU/DSU. The RS-232 interface is capable of communicating to another router or a PPP client machine over a modem, 56K CSU/DSU, or ISDN Terminal Adapter.

V.35 Interface

The MicroRouter 1220i does not include a V.35 cable. These cables are available from your reseller, or a number of other suppliers. The MicroRouter 1220i has a female V.35 connector, as do virtually all line communications devices. Thus, the V.35 cable required to connect to a line communications device will usually have male connectors at both ends. The pinouts for this cable are shown in Appendix B.

Image 13
Contents MicroRouter Installation Guide Page Introduction Network InstallationGetting Started CompatiView Software Installation Basic Configuration GuideAppendix B Connector and Cable Pin Outs Appendix a Shipping DefaultsSystems Appendix E Terms and Conditions About the MicroRouter IntroductionIntroduction Getting Started MicroRouter 1220i Installation OverviewCompatiView Software Installation Introduction Network InstallationCommand Line Preparation Basic Configuration GuidePage Getting Started Warranty and ServiceFew Notes Please Read The ManualsWhat You Will Need To Get Started Needed For InstallationSupplied with the MicroRouter Ethernet Connection RequirementsGetting Started 10Base-T Twisted-Pair Ethernet Telco Line Connection RequirementsInterface RS-232 Interface Placing the Router Network InstallationConnecting a Line Device to MicroRouter Connecting the Router to the EthernetConnecting to Twisted-Pair Ethernet Connecting Devices to the V.35 InterfaceConnecting Devices to the RS-232C Interface Connecting an Out-of-Band Management ConsolePowering Up the Router CompatiView for Windows Installation and OperationSystem Requirements Transport Protocols and CompatiView Out-of-Band Command Line Management Command Line ManagementCommand Line Management Setting Up Telnet OperationCommand Line Management Page Basic Configuration Guide IP Protocol Ethernet Interface ConfigurationRequired for IP Suggested for IPPhysical Communications Settings WAN Interface ConfigurationIPX Protocol Required for IPXRequired for Dedicated/Leased Line Operation Link ConfigurationSuggested for Dedicated/Leased Line Operation Required for Dial-On-Demand OperationIP Protocol Frame Relay Dlci Mappings Frame Relay ConfigurationRequired for IP Unnumbered Interface Required for IP Numbered InterfaceIPX Protocol Smds Addressing Saving a Configuration File to Flash ROMPage Ethernet Interfaces Appendix a Shipping DefaultsWAN Interfaces RS-232 WAN 1 Link & Physical Defaults WAN 0 Link & Physical DefaultsPin Outs for V.35 Female Connector DTE Appendix B Connector and Cable Pin OutsAppendix B Connector and Cable Pin Outs Ethernet Traffic Indicators Ethernet LED Bars Power On, No TrafficOther Indicators on All LED Bars Panic IndicatorsAppendix C LED Patterns and Test Switch Settings MicroRouter 1220i Switch SettingsAppendix D Downloading Software From Compatible Systems Page Appendix E Terms and Conditions Appendix E Terms ConditionsAppendix E Terms and Conditions Appendix E Terms and Conditions