Makita LS1016L dimensions Stopper

Page 21

Repair

[3] DISASSEMBLY/ASSEMBLY

[3]-10. Arm complete, Arm holder (cont.)

DISASSEMBLING

7) Remove CT 4x16 Tapping screw.

Arm holder cover and Position plate can be removed. (Fig. 55)

8)Pull out Center shaft while pushing Leaf spring as illustrated in Fig. 56.

9)After removing Leaf spring from Lock pin 8, pull out Lock pin 8 and Compression spring 6 in the direction with black arrow. (Fig. 57)

10)Attach a thin slotted screwdriver to Stop ring E-4, and strike the head of the screwdriver by hand. (Fig. 58)

Stop ring E-4, Cam and Lever 22 section can be removed.

11)Lever 22 section can be separated by removing M4x10 Pan head screw. (Fig. 59)

Fig. 56

Fig. 57

P 21/ 37

Fig. 55

Position plate

Arm holder cover

CT 4x16 Tapping screw

Groove of Lock pin 8

Leaf spring

Center shaft

Leaf spring

Lock pin 8

 

 

Compression spring 6

 

Arm holder complete

 

convex of Leaf spring

Fig. 58

Slotted screwdriver

Cam

Lever 22

 

 

section

Protrusion

 

 

of Cam

 

 

 

 

M4x10 Pan

Rod 6

 

head screw

Fig. 59

Lever 22 section

M4x10 Pan head screw

Stop ring E-4

ASSEMBLING

Take the disassembling step in reverse.

Rod 6

Fig. 60

Lever 22

Note: 1) Leaf spring has to be hooked with the groove of Lock pin 8. (Fig. 56)

2)Do not face the convex of Leaf spring to the opposite of Arm holder complete. (Fig. 57)

3)Pay attention to the direction of Rod 6. As illustrated in Figs 58 and 59. Tabs on the ends of Stop ring E-4 have to be fit between the protrusion of Cam and the flat portion of Rod 6. Tab on the center of Stop ring E-4 has to be fit into the groove of Cam.

4)M10-17 Hex lock nut illustrated in Fig. 52 has to be tighten to 3.5 up to 4.0N.m. using 1R254, 1R220, 1R222 and Socket assembly 17-38.

When Lever 105 is set in place and Handle is held by hand, Motor section has to be smoothly tilted without wobbling. Therefore, do fine adjustment of M10-17 Hex lock nut.

5) One end of Torsion spring 14 has to be hooked with Stopper.

The other of Torsion spring 14 has to be hooked with the center of Arm holder complete as illustrated in Fig. 60.

6)Lever 105 has to be secured at 0 up to 30 degrees tilted counter- clockwise (illustrated in light gray color) from the axial-symmetry position (illustrated in dark gray color) as illustrated in Fig. 61.

Flat washer 12

Stopper

Torsion spring 14

Retaining ring S-12

center of Arm

holder complete

 

Fig. 61

Lever 105

Image 21
Contents Specification Optional accessoriesStandard equipment Cutting Capacities Repair Necessary Repairing ToolsRepair Lubrications Spiral bevel gear 32 80 Helical gear Disassembling Repair DISASSEMBLY/ASSEMBLY 3-1. Blade case, Motor sectionCorrect Wrong Blade case, Motor sectionAssembling DISASSEMBLY/ASSEMBLY DISASSEMBLY/ASSEMBLY DISASSEMBLY/ASSEMBLY DISASSEMBLY/ASSEMBLY DISASSEMBLY/ASSEMBLY Safety lock mechanism 3mm Safety cover B Repair DISASSEMBLY/ASSEMBLY 3-4. Safety cover a Turn Base, Base Positive lock mechanism of Turn base Stopper pin Assembling of Square rod completeArm complete, Arm holder Front arm sectionStopper Laser Mechanism for LS1016L only Lower-slide lock mechanism AdjustmentBlade Guide fenceLaser for LS1016L only Adjustment Motor housing Circuit diagramHandle cover Handle sectionUK 110V only Handle cover Handle sectionArgentine Fig. D-1D 110-127V area except UK Inside of Case Outside of Case Wiring diagramFig. D-2A Fig. D-2D Fig. D-2E Wiring in Motor housing and Handle for UK Laser circuit section viewed from front side