Always Support Long Pieces | DeWalt DW717 specification

English

For varied cutting applications, refer to the list of recommended saw blades for your saw and select the one that best fits your needs (Page 5).

BODY AND HAND POSITION (FIG. 13A)

Proper positioning of your body and hands when operating the miter saw will make cutting easier, more accurate and safer. Never place hands near cutting area. Place hands no closer than 6" (152.4 mm) from the blade. Hold the workpiece tightly to the table and the fence when cutting. Keep hands in position until the trigger has been released and the blade has completely stopped. ALWAYS MAKE DRY RUNS (UNPOWERED) BEFORE FINISH CUTS SO THAT YOU CAN CHECK THE PATH OF THE BLADE. DO NOT CROSS HANDS, AS SHOWN IN FIGURE 13B. Keep both feet firmly on the floor and maintain proper balance. As you move the miter arm left and right, follow it and stand slightly to the side of the saw blade. Sight through the guard louvers when following a pencil line.

CLAMPING THE WORKPIECE

WARNING: To reduce the risk of serious personal injury, turn off the tool and disconnect it from the power source before attempting to move it, change accessories or make any adjustments accept as written in laser adjustment instructions.

WARNING: A workpiece that is clamped, balanced and secure before a cut may become unbalanced after a cut is completed. An unbalanced load may tip the saw or anything the saw is attached to, such as a table or workbench. When making a cut that may become unbalanced, properly support the workpiece and ensure the saw is firmly bolted to a stable surface. Personal injury may occur.

WARNING: The clamp foot must remain clamped above the base of the saw whenever the clamp is used. Always clamp the workpiece to the base of the saw–not to any other part of the work area. Ensure the clamp foot is not clamped on the edge of the base of the saw.

If you cannot secure the workpiece on the table and against the fence by hand, (irregular shape, etc.) or your hand would be less than 6" (152.4 mm) from the blade, a clamp or other fixture must be used.

For best results use the DW7082 clamp made for use with your saw. Another type of clamp may be supplied with your DW717. To purchase the DW7082 contact your local retailer or DEWALT service center.

Other aids such as spring clamps, bar clamps or C-clamps may be appropriate for certain sizes and shapes of material. Use care in selecting and placing these clamps. Take time to make a dry run before making the cut. The left or right fence will slide from side to side to aid in clamping.

FIG. 14

FIG. 15

FIG. 16

ANGLE “A”

TO INSTALL CLAMP

1.Insert it into the hole behind the fence. The clamp should be facing toward the back of the miter saw. The groove on the clamp rod should be fully inserted into the base. Ensure this groove is fully inserted into the base of the miter saw.

If the groove is visible, the clamp will not be secure.

2.Rotate the clamp 180º toward the front of the miter saw.

3.Loosen the knob to adjust the clamp up or down, then use the fine adjust knob to firmly clamp the workpiece.

NOTE: Place the clamp on the opposite side of the base when beveling. ALWAYS MAKE DRY RUNS (UNPOWERED) BEFORE FINISH CUTS TO CHECK THE PATH OF THE BLADE. ENSURE THE CLAMP DOES NOT INTERFERE WITH THE ACTION OF THE SAW OR GUARDS.

SUPPORT FOR LONG PIECES

ALWAYS SUPPORT LONG PIECES.

Never use another person as a substitute for a table extension; as additional support for a workpiece that is longer or wider than the basic miter saw table or to help feed, support or pull the workpiece.

For best results, use the DW7080 extension work support to extend the table width of your saw. Available from your dealer at extra cost. Support long workpieces using any convenient means such as sawhorses or similar devices to keep the ends from dropping.

CUTTING PICTURE FRAMES, SHADOW BOXES AND OTHER FOUR-SIDED PROJECTS

To best understand how to make the items listed here, we suggest that you try a few simple projects using scrap wood until you develop a “FEEL” for your saw.

Your saw is the perfect tool for mitering corners like the one shown in Figure 14. Sketch A in Figure 15 shows a joint made by using the bevel adjustment to bevel the edges of the two boards at 45º each to produce a 90º corner. For this joint the miter arm was locked in the zero position and the bevel adjustment was locked at 45º. The wood was positioned with the broad flat side against the table and the narrow edge against the fence. The cut could also be made by mitering right and left with the broad surface against the fence.

CUTTING TRIM MOLDING AND OTHER FRAMES

Sketch B in Figure 14 shows a joint made by setting the miter arm at 45º to miter the two boards to form a 90º corner. To make this type of joint, set the bevel adjustment to zero and the miter arm to 45º. Once again, position the wood with the broad flat side on the table and the narrow edge against the fence.

The two sketches in Figure 15 are for four side objects only.

As the number of sides changes, so do the miter and bevel angles. The chart below gives the proper angles for a variety of shapes.

(The chart assumes that all sides are of equal length.) For a shape that is not shown in the chart, use the following formula. 180º divided by the number of sides equals the miter (if the material is cut vertically) or bevel angle (if the material is cut laying flat).

	- EXAMPLES -
NO. SIDES		ANGLE MITER OR BEVEL
4		45°
5		36°
6		30°
7		25.7°
8		22.5°
9		20°
10		18°

DW717 specifications

The DeWalt DW717 is a powerful and versatile 10-inch dual bevel sliding compound miter saw designed to meet the demands of both professional carpenters and DIY enthusiasts. Known for its durability, precision, and ease of use, the DW717 has become a popular choice for those seeking accurate cuts in a variety of materials.

One of the standout features of the DW717 is its dual bevel capability, which allows users to make precise beveled cuts in both left and right directions. This feature eliminates the need to flip the workpiece, saving valuable time and enhancing overall efficiency. The saw also boasts an impressive crosscut capacity, capable of cutting through wider materials, making it ideal for large-scale projects such as framing and crown molding.

The DW717 is equipped with a powerful 15-amp motor that delivers robust performance for tough cutting tasks. It operates at an impressive no-load speed of 3,800 RPM, ensuring clean and smooth cuts through various materials, including hardwood and softwood. The saw’s motor is designed for high efficiency, providing users with the power needed for continuous operation without overheating.

Another notable technology incorporated into the DW717 is its precision miter system, which offers positive stops at commonly used angles. This feature ensures quick adjustments and accurate cuts, making it easier for users to switch between different angles quickly. The saw includes a miter scale with easy-to-read indicators, allowing for effortless angle setting.

Additionally, the DW717 features an adjustable sliding fence that provides support for larger materials, ensuring stability and precision during cuts. The saw’s lightweight design and built-in carrying handle enhance portability, making it easy to transport to job sites.

Safety features are also a top priority with the DW717. The saw is equipped with a blade guard that protects users from accidental contact with the blade, while the electric brake ensures quick stopping of the blade after the trigger is released.

In summary, the DeWalt DW717 is a well-engineered tool, combining power, precision, and safety for a wide range of cutting tasks. With its dual bevel capabilities, impressive motor, and user-friendly features, it stands out as a reliable choice for both professionals and hobbyists alike. Whether you are tackling framing, molding, or other intricate cuts, the DW717 is built to deliver exceptional performance and results every time.