HP 2103R-CSDI manual Quick Installation

Page 29

Quick Installation

2-5

Quick Installation Follow the general steps outlined in Table 2-2 to install and configure the for Managed Hubs Edge Router module in a managed ONline or ONcore hub.

Table 2-2 Quick Installation for Managed Hubs

Step	Procedure	Refer to:

1	Unpack the module.	Unpacking Procedures on page 2-6
2	Verify the jumper plug positions on	Verifying Jumper Plug Positions on
	the base and expansion engines	page 2-7

3Insert the module into an open slot in the hub.

The appropriate installation instructions for your hub type in this chapter

4	Configure the carrier for possible	Configuring DIP Switches on page 2-8
	operation in an unmanaged hub.

5Attach a management terminal to the Edge Router console port.

6Configure the carrier using network management commands.

Configuring the Edge Router Engine on page 3-9

Configuring the Carrier in a Managed ONline Hub on page 3-4

or

Configuring the Carrier in a Managed ONcore Hub on page 3-5

7	Configure the engine parameters	Cisco Systems Getting Started Guide
	using Cisco Systems setup
	command.
8	Attach WAN cables to the 60-pin	Cable Pinouts on page A-5
	universal WAN connectors on the
	front panel.

Image 29

Contents Edge Router Module Installation Guide For Ethernet 3Com Corporation 5400 Bayfront Plaza Santa Clara, California Iii Page Contents Configuring the Edge Router Module Monitoring Edge Router Module Operation Index Limited Warranty About this Guide How to Use This GuideIntroduction AudienceList conventions used throughout this guide ConventionsCommands Documents Related3Com Documents Cisco DocumentsInternational and Hughes LAN Systems, May Page Introduction LAN Product Overview Shows the architecture of each Edge Router module type Including Module FeaturesEdge Router IP/IPX Edge Router Module Features Ethernet LAN Edge Router Module Memory Configurations Feature Set Desktop Memory Type Page Installing the Edge Router Module Configure the Edge Router module InstallationFlowchart Procedures PrecautionaryQuick Installation Router moduleCisco Systems Getting Started Guide Quick Installation Unpacking Edge Router Module Installation Guide for EthernetPlug Positions Verifying JumperSwitches Configuring DIPIsolating the ONline Edge Router Module ConfiguringONcore Carrier DIP Parameters Switches Enabling or Disabling Nvram Configuration Shows the ONcore carrier DIP switch locationTo select a network Set the switches according to Table If the NV SEL DIP switch isIf you are installing InstallingONline Edge Router ModuleThis is called a hot swap To install the Edge Router module in an ONcore hubONcore Edge Installing the Edge Router Module in an ONcore Hub Opened and Closed Module Ejectors Close the ejectors FigurePage Router Module Overview ConfigurationManaged Terminal Attaching aManagement Hub Selecting a Network Saving the ConfigurationCarrier in a ConfiguringManaged ONcore This section contains the following topicsCarrier Default Settings Configuring the Carrier in a Managed ONcore Hub DMM DIP Nvram DIP Terminal to Auxiliary port Console Port Attaching a Terminal Cable to the Console Port Mini-DIN connector pinouts are provided in Appendix a Page Operation Module OperationMonitoring Edge Edge Router Module LEDs Showing Module Following network management module commandsStatus Each LED is described in TableModule Command Syntax for the Show Module command is Using the ShowONline show module 6 verbose Edge Router module installed in slot 1 of an ONcore hub Port Command Ports Syntax for the Show Port command isONcore show port Page Troubleshooting Troubleshooting Troubleshooting Network Connectivity Problems Problems Operating CorrectingMalfunctions MalfunctionsSeconds, and then power it on Specifications Electrical General SpecificationsMechanical Specifications Environmental Specifications5006C-FT Cable Pinouts Cables when you install all equipmentOpenHub Management Cable Part Number OHPMGT-CAB OpenHub Management Cable has aDTR CTS TXD CTS Cable Pinouts DTE DCE Ltst CS+ SCTE+ Table A-17 X.21 DTE and DCE Cable Pinouts DB-15 15 Pin Online Technical ServicesThrough the following online systems Days a week, 24 hours a day408 Access by Digital ModemPress Return to view the 3ComForum main menu Supplier Support FromYour Network To find your authorized service provider U.S. and Canada, call 800 876-3266 for customer service3Com CorporationContacting 3Com ISD Technical Publications Accessing the 3Com ISD MIBTo exit the FTP session, invoke the quit command Numerics IndexQuick Software 1-8Upgrading Firmware 1-8 memory Page Limited Warranty 408 764-5000 3/18/96