HP 2103R-CSDI manual Dte Dce

Page 76

A-10 APPENDIX A: SPECIFICATIONS

EIA-530 DTE Synchronous Serial Cable Pinouts

Table A-13 lists pinouts for EIA-530 DTE synchronous serial cable (Part Number ERM530-CAB).

Table A-13

EIA-530 DTE Cable Pinouts (DB-25)

 

 

 

 

 

 

 

 

 

 

Direction

 

 

DTE DCE

25 Pin1

Signal

DTE DCE2

25 Pin

Signal

Direction

J2-1

Shield

J2-8

CF(A), DCD+

J2-10

CF(B), DCD-

 

 

 

 

 

 

J2-2

BA(A), TxD+

J2-15

DB(A), TxC+

J2-14

BA(B), TxD-

J2-12

DB(B), TxC-

 

 

 

 

 

 

J2-3

BB(A), RxD+

J2-17

DD(A), RxC+

J2-16

BB(B), RxD-

J2-9

DD(B), RxC-

 

 

 

 

 

 

J2-4

CA(A), RTS+

J2-18

LL

J2-19

CA(B), RTS-

J2-7

Circuit GND

 

 

 

 

 

 

J2-5

CB(A), CTS+

J2-20

CD(A), DTR+

J2-13

CB(B), CTS-

J2-23

CD(B), DTR-

 

 

 

 

 

 

J2-6

CC(A), DSR+

J2-24

DA(A), TxCE+

J2-22

CC(B), DSR-

J2-11

DA(B), TxCE-

1Any pin not referenced is not connected.

2The EIA-530 interface cannot be operated in DCE mode. A DCE cable is not available for the EIA-530 interface.

Image 76
Contents Edge Router Module Installation Guide For Ethernet 3Com Corporation 5400 Bayfront Plaza Santa Clara, California Iii Page Contents Configuring the Edge Router Module Monitoring Edge Router Module Operation Index Limited Warranty How to Use This Guide About this GuideIntroduction AudienceConventions List conventions used throughout this guideCommands Related Documents3Com Documents Cisco DocumentsInternational and Hughes LAN Systems, May Page Introduction LAN Product Overview Shows the architecture of each Edge Router module type Edge Router Module FeaturesIncluding IP/IPX Edge Router Module Features Ethernet LAN Edge Router Module Memory Configurations Feature Set Desktop Memory Type Page Installing the Edge Router Module Flowchart InstallationConfigure the Edge Router module Precautionary ProceduresQuick Installation Router moduleCisco Systems Getting Started Guide Quick Installation Edge Router Module Installation Guide for Ethernet UnpackingVerifying Jumper Plug PositionsConfiguring DIP SwitchesONcore Carrier DIP Parameters Switches ConfiguringIsolating the ONline Edge Router Module Shows the ONcore carrier DIP switch location Enabling or Disabling Nvram ConfigurationIf the NV SEL DIP switch is To select a network Set the switches according to TableInstalling If you are installingONline Edge Router ModuleONcore Edge To install the Edge Router module in an ONcore hubThis is called a hot swap Installing the Edge Router Module in an ONcore Hub Close the ejectors Figure Opened and Closed Module EjectorsPage Router Module Managed ConfigurationOverview Management Attaching aTerminal Selecting a Network Saving the Configuration HubConfiguring Carrier in aManaged ONcore This section contains the following topicsCarrier Default Settings Configuring the Carrier in a Managed ONcore Hub DMM DIP Nvram DIP Terminal to Auxiliary port Console Port Attaching a Terminal Cable to the Console Port Mini-DIN connector pinouts are provided in Appendix a Page Monitoring Edge Module OperationOperation Edge Router Module LEDs Following network management module commands Showing ModuleStatus Each LED is described in TableUsing the Show Module Command Syntax for the Show Module command isONline show module 6 verbose Port Command Ports Syntax for the Show Port command is Edge Router module installed in slot 1 of an ONcore hubONcore show port Page Troubleshooting Troubleshooting Troubleshooting Network Connectivity Problems Problems Correcting OperatingMalfunctions MalfunctionsSeconds, and then power it on Specifications General Specifications ElectricalEnvironmental Specifications Mechanical Specifications5006C-FT Cables when you install all equipment Cable PinoutsOpenHub Management Cable Part Number OHPMGT-CAB OpenHub Management Cable has aDTR CTS TXD CTS Cable Pinouts DTE DCE Ltst CS+ SCTE+ Table A-17 X.21 DTE and DCE Cable Pinouts DB-15 15 Pin Services Online TechnicalThrough the following online systems Days a week, 24 hours a dayAccess by Digital Modem 408Press Return to view the 3ComForum main menu Your Network Support FromSupplier U.S. and Canada, call 800 876-3266 for customer service To find your authorized service provider3Com CorporationTo exit the FTP session, invoke the quit command Accessing the 3Com ISD MIBContacting 3Com ISD Technical Publications Index NumericsQuick Software 1-8Upgrading Firmware 1-8 memory Page Limited Warranty 408 764-5000 3/18/96