HP 2103R-CSDI manual Verifying Jumper, Plug Positions

Page 31

Verifying Jumper Plug Positions

2-7

Verifying Jumper	Verify the jumper plug positions on the ONline or ONcore Edge Router
Plug Positions	module before proceeding with the installation procedure.
	The Edge Router module is equipped with several jumper plugs. The
	jumpers are factory-set to the appropriate settings. Do not modify the
	jumper settings, except to restore the settings to the required positions.
	CAUTION: If you modify any of the factory-set jumper positions, the Edge
	Router module may not operate properly.
	Table 2-3 lists the default jumper plug positions for the Edge Router
	module. If you suspect that any of the jumper positions have been changed,
	verify the plug positions using Table 2-3.
	.
	Table 2-3 Default Jumper Plug Settings

Jumper	Jumper Plug Position

J1	ETH INT

J2	Removed

J4	Inserted

J5	Removed

J9	Removed

J10	WAN 0 EXT

J12	WAN 1 EXT

J13	Removed

J14	Inserted

J15	Removed

J16	Inserted

J17	Inserted

Image 31

Contents Edge Router Module Installation Guide For Ethernet 3Com Corporation 5400 Bayfront Plaza Santa Clara, California Iii Page Contents Configuring the Edge Router Module Monitoring Edge Router Module Operation Index Limited Warranty Audience How to Use This GuideAbout this Guide IntroductionList conventions used throughout this guide ConventionsCommands Cisco Documents RelatedDocuments 3Com DocumentsInternational and Hughes LAN Systems, May Page Introduction LAN Product Overview Shows the architecture of each Edge Router module type Edge Router Module FeaturesIncluding IP/IPX Edge Router Module Features Ethernet LAN Edge Router Module Memory Configurations Feature Set Desktop Memory Type Page Installing the Edge Router Module Flowchart InstallationConfigure the Edge Router module Router module PrecautionaryProcedures Quick InstallationCisco Systems Getting Started Guide Quick Installation Unpacking Edge Router Module Installation Guide for EthernetPlug Positions Verifying JumperSwitches Configuring DIPONcore Carrier DIP Parameters Switches ConfiguringIsolating the ONline Edge Router Module Enabling or Disabling Nvram Configuration Shows the ONcore carrier DIP switch locationTo select a network Set the switches according to Table If the NV SEL DIP switch isRouter Module InstallingIf you are installing ONline EdgeONcore Edge To install the Edge Router module in an ONcore hubThis is called a hot swap Installing the Edge Router Module in an ONcore Hub Opened and Closed Module Ejectors Close the ejectors FigurePage Router Module Managed ConfigurationOverview Management Attaching aTerminal Hub Selecting a Network Saving the ConfigurationThis section contains the following topics ConfiguringCarrier in a Managed ONcoreCarrier Default Settings Configuring the Carrier in a Managed ONcore Hub DMM DIP Nvram DIP Terminal to Auxiliary port Console Port Attaching a Terminal Cable to the Console Port Mini-DIN connector pinouts are provided in Appendix a Page Monitoring Edge Module OperationOperation Edge Router Module LEDs Each LED is described in Table Following network management module commandsShowing Module StatusModule Command Syntax for the Show Module command is Using the ShowONline show module 6 verbose Edge Router module installed in slot 1 of an ONcore hub Port Command Ports Syntax for the Show Port command isONcore show port Page Troubleshooting Troubleshooting Troubleshooting Network Connectivity Problems Problems Malfunctions CorrectingOperating MalfunctionsSeconds, and then power it on Specifications Electrical General SpecificationsMechanical Specifications Environmental Specifications5006C-FT OpenHub Management Cable has a Cables when you install all equipmentCable Pinouts OpenHub Management Cable Part Number OHPMGT-CABDTR CTS TXD CTS Cable Pinouts DTE DCE Ltst CS+ SCTE+ Table A-17 X.21 DTE and DCE Cable Pinouts DB-15 15 Pin Days a week, 24 hours a day ServicesOnline Technical Through the following online systems408 Access by Digital ModemPress Return to view the 3ComForum main menu Your Network Support FromSupplier Corporation U.S. and Canada, call 800 876-3266 for customer serviceTo find your authorized service provider 3ComTo exit the FTP session, invoke the quit command Accessing the 3Com ISD MIBContacting 3Com ISD Technical Publications Numerics IndexQuick Software 1-8Upgrading Firmware 1-8 memory Page Limited Warranty 408 764-5000 3/18/96